![](http://image.absoluteastronomy.com/images//topicimages/noimage.gif)
Foil (fluid mechanics)
Encyclopedia
A foil is a solid object with a shape such that when placed in a moving fluid
at a suitable angle of attack
the lift
(force generated perpendicular to the fluid flow) is substantially larger than the drag
(force generated parallel the fluid flow). If the fluid is a gas
, the foil is called an airfoil
and if the fluid is water
the foil is called a hydrofoil
.
A foil generates lift primarily as a result of its shape and angle of attack
. When oriented at a suitable angle, the foil deflects the oncoming fluid, resulting in a force on the foil in the direction opposite to the deflection. This force can be resolved into two components: lift
and drag
. This "turning" of the fluid in the vicinity of the foil creates curved streamlines which results in lower pressure on one side and higher pressure on the other. This pressure difference is accompanied by a velocity difference, via Bernoulli's principle
, so the resulting flowfield about the foil has a higher average velocity on the upper surface than on the lower surface.
A more detailed description of the flowfield is given by the Navier-Stokes Equations, which is applicable when the fluid is incompressible. However, since the effects of the compressibility of air at low speeds is negligible, the Navier-Stokes equations can be used for both airfoils and hydrofoils as long as the fluid flow is substantially less than the speed of sound.
) to the flow the plate will deflect the fluid passing over and under it, and this deflection
will result in a lift force on the plate. However, while it does generate lift, it also generates a large amount of drag.
Since even a simple flat plate can generate lift, a significant factor in foil design is the minimization of drag. An example of this is the rudder
of a boat or aircraft. When designing a rudder a key design factor is the minimization of drag in its neutral position, which is balanced with the need to produce sufficient lift with which to turn the craft at a reasonable rate.
Other types of foils, both natural and man-made, seen both in air and water, have features that delay or control the onset of lift-induced drag
, flow separation
, and stall
(see Bird flight
, Fin
, Airfoil
, Denticle, Tubercle
, Vortex generator
, Canard
(close-coupled), Blown flap
, Leading edge slot
, Leading edge slats
), as well as Wingtip vortices
(see Winglet
).
Fluid
In physics, a fluid is a substance that continually deforms under an applied shear stress. Fluids are a subset of the phases of matter and include liquids, gases, plasmas and, to some extent, plastic solids....
at a suitable angle of attack
Angle of attack
Angle of attack is a term used in fluid dynamics to describe the angle between a reference line on a lifting body and the vector representing the relative motion between the lifting body and the fluid through which it is moving...
the lift
Lift (force)
A fluid flowing past the surface of a body exerts a surface force on it. Lift is the component of this force that is perpendicular to the oncoming flow direction. It contrasts with the drag force, which is the component of the surface force parallel to the flow direction...
(force generated perpendicular to the fluid flow) is substantially larger than the drag
Drag (physics)
In fluid dynamics, drag refers to forces which act on a solid object in the direction of the relative fluid flow velocity...
(force generated parallel the fluid flow). If the fluid is a gas
Gas
Gas is one of the three classical states of matter . Near absolute zero, a substance exists as a solid. As heat is added to this substance it melts into a liquid at its melting point , boils into a gas at its boiling point, and if heated high enough would enter a plasma state in which the electrons...
, the foil is called an airfoil
Airfoil
An airfoil or aerofoil is the shape of a wing or blade or sail as seen in cross-section....
and if the fluid is water
Water
Water is a chemical substance with the chemical formula H2O. A water molecule contains one oxygen and two hydrogen atoms connected by covalent bonds. Water is a liquid at ambient conditions, but it often co-exists on Earth with its solid state, ice, and gaseous state . Water also exists in a...
the foil is called a hydrofoil
Hydrofoil
A hydrofoil is a foil which operates in water. They are similar in appearance and purpose to airfoils.Hydrofoils can be artificial, such as the rudder or keel on a boat, the diving planes on a submarine, a surfboard fin, or occur naturally, as with fish fins, the flippers of aquatic mammals, the...
.
Physics of foils
![](http://image.absoluteastronomy.com/images/encyclopediaimages/s/st/streamlines_around_a_naca_0012.svg.png)
Angle of attack
Angle of attack is a term used in fluid dynamics to describe the angle between a reference line on a lifting body and the vector representing the relative motion between the lifting body and the fluid through which it is moving...
. When oriented at a suitable angle, the foil deflects the oncoming fluid, resulting in a force on the foil in the direction opposite to the deflection. This force can be resolved into two components: lift
Lift (force)
A fluid flowing past the surface of a body exerts a surface force on it. Lift is the component of this force that is perpendicular to the oncoming flow direction. It contrasts with the drag force, which is the component of the surface force parallel to the flow direction...
and drag
Drag (physics)
In fluid dynamics, drag refers to forces which act on a solid object in the direction of the relative fluid flow velocity...
. This "turning" of the fluid in the vicinity of the foil creates curved streamlines which results in lower pressure on one side and higher pressure on the other. This pressure difference is accompanied by a velocity difference, via Bernoulli's principle
Bernoulli's principle
In fluid dynamics, Bernoulli's principle states that for an inviscid flow, an increase in the speed of the fluid occurs simultaneously with a decrease in pressure or a decrease in the fluid's potential energy...
, so the resulting flowfield about the foil has a higher average velocity on the upper surface than on the lower surface.
A more detailed description of the flowfield is given by the Navier-Stokes Equations, which is applicable when the fluid is incompressible. However, since the effects of the compressibility of air at low speeds is negligible, the Navier-Stokes equations can be used for both airfoils and hydrofoils as long as the fluid flow is substantially less than the speed of sound.
Basic design considerations
The degenerate case of a foil is a simple flat plate. When set at an angle (the angle of attackAngle of attack
Angle of attack is a term used in fluid dynamics to describe the angle between a reference line on a lifting body and the vector representing the relative motion between the lifting body and the fluid through which it is moving...
) to the flow the plate will deflect the fluid passing over and under it, and this deflection
Deflection (physics)
In physics deflection is the event where an object collides and bounces against a plane surface.In such collisions involving a sphere and a plane, the collision angle formed with the surface normal must equal the bounce angle , \alpha = \beta.Magnetic deflection refers to Lorentz forces acting...
will result in a lift force on the plate. However, while it does generate lift, it also generates a large amount of drag.
Since even a simple flat plate can generate lift, a significant factor in foil design is the minimization of drag. An example of this is the rudder
Rudder
A rudder is a device used to steer a ship, boat, submarine, hovercraft, aircraft or other conveyance that moves through a medium . On an aircraft the rudder is used primarily to counter adverse yaw and p-factor and is not the primary control used to turn the airplane...
of a boat or aircraft. When designing a rudder a key design factor is the minimization of drag in its neutral position, which is balanced with the need to produce sufficient lift with which to turn the craft at a reasonable rate.
Other types of foils, both natural and man-made, seen both in air and water, have features that delay or control the onset of lift-induced drag
Lift-induced drag
In aerodynamics, lift-induced drag, induced drag, vortex drag, or sometimes drag due to lift, is a drag force that occurs whenever a moving object redirects the airflow coming at it. This drag force occurs in airplanes due to wings or a lifting body redirecting air to cause lift and also in cars...
, flow separation
Flow separation
All solid objects travelling through a fluid acquire a boundary layer of fluid around them where viscous forces occur in the layer of fluid close to the solid surface. Boundary layers can be either laminar or turbulent...
, and stall
Stall
In fluid dynamics, a stall is a reduction in the lift coefficient generated by a foil as angle of attack increases. This occurs when the critical angle of attack of the foil is exceeded...
(see Bird flight
Bird flight
Flight is the main mode of locomotion used by most of the world's bird species. Flight assists birds while feeding, breeding and avoiding predators....
, Fin
Fin
A fin is a surface used for stability and/or to produce lift and thrust or to steer while traveling in water, air, or other fluid media, . The first use of the word was for the limbs of fish, but has been extended to include other animal limbs and man-made devices...
, Airfoil
Airfoil
An airfoil or aerofoil is the shape of a wing or blade or sail as seen in cross-section....
, Denticle, Tubercle
Tubercle
A tubercle is generally a wart-like projection, but it has slightly different meaning depending on which family of plants or animals it is used to refer to....
, Vortex generator
Vortex generator
A vortex generator is an aerodynamic surface, consisting of a small vane or bump that creates a vortex. Vortex generators can be found on many devices, but the term is most often used in aircraft design....
, Canard
Canard (aeronautics)
In aeronautics, canard is an airframe configuration of fixed-wing aircraft in which the forward surface is smaller than the rearward, the former being known as the "canard", while the latter is the main wing...
(close-coupled), Blown flap
Blown flap
Blown flaps are a powered aerodynamic high-lift device invented by the British and used on the wings of certain aircraft to improve low-speed lift during takeoff and landing. The process is sometimes called a boundary layer control system . They were a popular design feature in the 1960s, but fell...
, Leading edge slot
Leading edge slot
A leading edge slot is an aerodynamic feature of the wing of some aircraft to reduce the stall speed and promote good low-speed handling qualities. A leading edge slot is a span-wise gap in each wing, allowing air to flow from below the wing to its upper surface...
, Leading edge slats
Leading edge slats
Slats are aerodynamic surfaces on the leading edge of the wings of fixed-wing aircraft which, when deployed, allow the wing to operate at a higher angle of attack. A higher coefficient of lift is produced as a result of angle of attack and speed, so by deploying slats an aircraft can fly at slower...
), as well as Wingtip vortices
Wingtip vortices
Wingtip vortices are tubes of circulating air that are left behind a wing as it generates lift. One wingtip vortex trails from the tip of each wing. The cores of vortices spin at very high speed and are regions of very low pressure...
(see Winglet
Winglet
Wingtip devices are usually intended to improve the efficiency of fixed-wing aircraft. There are several types of wingtip devices, and though they function in different manners, the intended effect is always to reduce the aircraft's drag by partial recovery of the tip vortex energy...
).
See also
- FluidFluidIn physics, a fluid is a substance that continually deforms under an applied shear stress. Fluids are a subset of the phases of matter and include liquids, gases, plasmas and, to some extent, plastic solids....
- SurfaceSurfaceIn mathematics, specifically in topology, a surface is a two-dimensional topological manifold. The most familiar examples are those that arise as the boundaries of solid objects in ordinary three-dimensional Euclidean space R3 — for example, the surface of a ball...
- Lift (force)Lift (force)A fluid flowing past the surface of a body exerts a surface force on it. Lift is the component of this force that is perpendicular to the oncoming flow direction. It contrasts with the drag force, which is the component of the surface force parallel to the flow direction...
- Drag (force)
- Lift-induced dragLift-induced dragIn aerodynamics, lift-induced drag, induced drag, vortex drag, or sometimes drag due to lift, is a drag force that occurs whenever a moving object redirects the airflow coming at it. This drag force occurs in airplanes due to wings or a lifting body redirecting air to cause lift and also in cars...
- Fluid dynamicsFluid dynamicsIn physics, fluid dynamics is a sub-discipline of fluid mechanics that deals with fluid flow—the natural science of fluids in motion. It has several subdisciplines itself, including aerodynamics and hydrodynamics...
- Bernoulli's principleBernoulli's principleIn fluid dynamics, Bernoulli's principle states that for an inviscid flow, an increase in the speed of the fluid occurs simultaneously with a decrease in pressure or a decrease in the fluid's potential energy...
- Coanda effectCoanda effectThe Coandă effect is the tendency of a fluid jet to be attracted to a nearby surface. The principle was named after Romanian aerodynamics pioneer Henri Coandă, who was the first to recognize the practical application of the phenomenon in aircraft development....
- Newton's laws of motion#Newton's third law
- FinFinA fin is a surface used for stability and/or to produce lift and thrust or to steer while traveling in water, air, or other fluid media, . The first use of the word was for the limbs of fish, but has been extended to include other animal limbs and man-made devices...
- Flipper (anatomy)Flipper (anatomy)A flipper is a typically flat limb evolved for movement through water. Various creatures have evolved flippers, for example penguins , cetaceans A flipper is a typically flat limb evolved for movement through water. Various creatures have evolved flippers, for example penguins (also called...
- KeelKeelIn boats and ships, keel can refer to either of two parts: a structural element, or a hydrodynamic element. These parts overlap. As the laying down of the keel is the initial step in construction of a ship, in British and American shipbuilding traditions the construction is dated from this event...
(hydrodynamic) - AirfoilAirfoilAn airfoil or aerofoil is the shape of a wing or blade or sail as seen in cross-section....
- WingWingA wing is an appendage with a surface that produces lift for flight or propulsion through the atmosphere, or through another gaseous or liquid fluid...
- Chord (aircraft)Chord (aircraft)In aeronautics, chord refers to the imaginary straight line joining the trailing edge and the center of curvature of the leading edge of the cross-section of an airfoil...
- SailSailA sail is any type of surface intended to move a vessel, vehicle or rotor by being placed in a wind—in essence a propulsion wing. Sails are used in sailing.-History of sails:...
(aerodynamics) - Surfboard fin
- RudderRudderA rudder is a device used to steer a ship, boat, submarine, hovercraft, aircraft or other conveyance that moves through a medium . On an aircraft the rudder is used primarily to counter adverse yaw and p-factor and is not the primary control used to turn the airplane...
- Spoiler (automotive)Spoiler (automotive)A spoiler is an automotive aerodynamic device whose intended design function is to 'spoil' unfavorable air movement across a body of a vehicle in motion. Spoilers on the front of a vehicle are often called air dams, because in addition to directing air flow they also reduce the amount of air...
- DownforceDownforceDownforce is a downwards thrust created by the aerodynamic characteristics of a car. The purpose of downforce is to allow a car to travel faster through a corner by increasing the vertical force on the tires, thus creating more grip....
- Formula One carFormula One carA modern Formula One car is a single-seat, open cockpit, open wheel racing car with substantial front and rear wings, and an engine positioned behind the driver. The regulations governing the cars are unique to the championship...
- PropellerPropellerA propeller is a type of fan that transmits power by converting rotational motion into thrust. A pressure difference is produced between the forward and rear surfaces of the airfoil-shaped blade, and a fluid is accelerated behind the blade. Propeller dynamics can be modeled by both Bernoulli's...
- PlanformPlanformIn aviation, a planform is the shape and layout of a fixed-wing aircraft's fuselage and wing. Of all the myriad planforms used, they can typically be grouped into those used for low-speed flight, found on general aviation aircraft, and those used for high-speed flight, found on many military...
- HydrofoilHydrofoilA hydrofoil is a foil which operates in water. They are similar in appearance and purpose to airfoils.Hydrofoils can be artificial, such as the rudder or keel on a boat, the diving planes on a submarine, a surfboard fin, or occur naturally, as with fish fins, the flippers of aquatic mammals, the...
- Airplane
- GliderGliderUnpowered aircraft are a group of aerial vehicles that can fly without onboard propulsion. They can be classified as gliders, balloons and kites. In this instance, 'flight' means a trajectory that is not merely a vertical descent such as a parachute. In the case of kites, the flight is obtained by...
- BoomerangBoomerangA boomerang is a flying tool with a curved shape used as a weapon or for sport.-Description:A boomerang is usually thought of as a wooden device, although historically boomerang-like devices have also been made from bones. Modern boomerangs used for sport are often made from carbon fibre-reinforced...
- AileronAileronAilerons are hinged flight control surfaces attached to the trailing edge of the wing of a fixed-wing aircraft. The ailerons are used to control the aircraft in roll, which results in a change in heading due to the tilting of the lift vector...
- Diving planeDiving planeA diving plane, also known as a hydroplane, is a control surface found on submarines which allow the vessel to pitch its bow and stern up or down to assist in the process of submerging or surfacing the boat, as well as controlling depth when submerged....
- Angle of attackAngle of attackAngle of attack is a term used in fluid dynamics to describe the angle between a reference line on a lifting body and the vector representing the relative motion between the lifting body and the fluid through which it is moving...
- Stall (flight)Stall (flight)In fluid dynamics, a stall is a reduction in the lift coefficient generated by a foil as angle of attack increases. This occurs when the critical angle of attack of the foil is exceeded...
- Wingtip vorticesWingtip vorticesWingtip vortices are tubes of circulating air that are left behind a wing as it generates lift. One wingtip vortex trails from the tip of each wing. The cores of vortices spin at very high speed and are regions of very low pressure...
- Flow separationFlow separationAll solid objects travelling through a fluid acquire a boundary layer of fluid around them where viscous forces occur in the layer of fluid close to the solid surface. Boundary layers can be either laminar or turbulent...
- Lift coefficientLift coefficientThe lift coefficient is a dimensionless coefficient that relates the lift generated by a lifting body, the dynamic pressure of the fluid flow around the body, and a reference area associated with the body...
- Drag coefficientDrag coefficientIn fluid dynamics, the drag coefficient is a dimensionless quantity that is used to quantify the drag or resistance of an object in a fluid environment such as air or water. It is used in the drag equation, where a lower drag coefficient indicates the object will have less aerodynamic or...
- Lift-induced dragLift-induced dragIn aerodynamics, lift-induced drag, induced drag, vortex drag, or sometimes drag due to lift, is a drag force that occurs whenever a moving object redirects the airflow coming at it. This drag force occurs in airplanes due to wings or a lifting body redirecting air to cause lift and also in cars...
- NACA airfoilNACA airfoilThe NACA airfoils are airfoil shapes for aircraft wings developed by the National Advisory Committee for Aeronautics . The shape of the NACA airfoils is described using a series of digits following the word "NACA." The parameters in the numerical code can be entered into equations to precisely...
External links
- http://www.grc.nasa.gov/WWW/k-12/airplane/right2.html
- http://www.grc.nasa.gov/WWW/k-12/airplane/lift1.html
- http://www.grc.nasa.gov/WWW/k-12/airplane/bernnew.html
- http://wright.nasa.gov/airplane/shape.html
- http://www.grc.nasa.gov/WWW/k-12/airplane/wrong2.html
- http://www.flickr.com/photos/trektrack/2388729621/
- http://www.youtube.com/watch?v=o81WIfjrt5I
- http://www.youtube.com/watch?v=A06L-npXvDM
- http://people.eku.edu/ritchisong/554notes3.html