Nano-RAM
Encyclopedia
Nano-RAM is a proprietary computer memory
technology from the company Nantero
. It is a type of nonvolatile random access memory based on the mechanical position of carbon nanotubes deposited on a chip-like substrate. In theory, the small size of the nanotubes allows for very high density memories. Nantero also refers to it as NRAM.
where a third terminal is used to switch the memory cell between memory states. The second generation NRAM technology is based on a two-terminal memory cell. The two-terminal cell has advantages such as a smaller cell size, better scalability to sub-20 nm nodes (see semiconductor device fabrication), and the ability to passivate the memory cell during fabrication.
Nantero's technology is based on a well-known effect that in a non-woven fabric matrix of carbon nanotubes (CNTs), crossed nanotubes can either be touching or slightly separated depending on their mechanical state. When close to each other, the carbon nanotubes come under the influence of Van der Waal's forces. Each NRAM "cell" consists of an interlinked network of CNTs located between two electrodes as illustrated in Fig. 1. The CNT fabric is located between two metal electrodes, which is defined and etched by photolithography
, and forms the NRAM cell.
The NRAM acts as a resistive non-volatile random access memory (RAM
) and can be placed in two or more resistive modes depending on the resistive state of the CNT fabric. When the CNTs are not in contact the resistance
state of the fabric is high and represents a 0 (zero) state. When the CNTs are brought into contact, the resistance state of the fabric is low and represents a 1 state. NRAM can act as a memory because the two resistive states of the CNTs are both very stable. In the OFF or 0 state, the CNTs (or a portion of them) are not in contact and remain in a separated state due to the stiffness of the CNTs resulting in a high resistance or low current measurement state between the top and bottom electrodes. In the ON or 1 state, the CNTs (or a portion of them) are in contact and remain in a contacted state due to Van der Waals forces between the CNTs resulting in a low resistance or high current measurement state between the top and bottom electrodes.
To switch the NRAM between states, a small voltage greater than the read voltage is applied between top and bottom electrodes. If the NRAM is in the 0 state, the voltage applied will cause an electrostatic attraction between the CNTs close each other causing a SET operation. After the applied voltage is removed, the CNTs remain in an ON or low resistance state due to physical adhesion (Van der Waals force) with an activation energy
(Ea) of approximately 5eV. If the NRAM cell is in the 1 state, applying a voltage greater than the read voltage will generate CNT phonon excitations with sufficient energy to separate the CNT junctions. This is the phonon driven RESET operation. The CNTs remain in the OFF or high resistance state due to the high mechanical stiffness (Young's Modulus
1 TPa) with an activation energy (Ea) much greater than 5 eV. Figure 2 illustrates both states of an individual pair of CNTs involved in the switch operation. Due to the high activation energy (> 5eV) required for switching between states, the NRAM switch shows excellent resistance to outside interference like radiation and operating temperature that can erase or flip conventional memories like DRAM
.
NRAMs are fabricated by depositing a uniform layer of CNTs onto a prefabricated array of drivers such as transistors as shown in Figure 1. The bottom electrode of the NRAM cell is in contact with the underlying via (electronics)
connecting the cell to the driver. The bottom electrode may be fabricated as part of the underlying via or it may be fabricated simultaneously with the NRAM cell, when the cell is photolithographically defined and etched. Before the cell is photolithographically defined and etched, the top electrode is deposited as a metal film onto the CNT layer so that the top metal electrode is patterned and etched during the definition of the NRAM cell. Following the dielectric passivation and fill of the array, the top metal electrode is exposed by etching back the overlying dielectric using a smoothing process such as CMP (Chemical-mechanical planarization
). With the top electrode exposed, the next level of metal wiring interconnect is fabricated to complete the NRAM array. Figure 3 illustrates one of the many circuit methods that can be used to select a single cell for writing and reading. Using a cross-grid interconnect arrangement, the NRAM and driver, (the cell), forms a memory array similar to other memory arrays such as DRAM or Flash memory
. A single cell can be selected by applying the proper voltages to the word line (WL), bit line (BL), and select lines (SL) without disturbing the other cells in the array.
Compared other NVRAM ("Non-Volatile RAM") technologies, NRAM has further advantages. The most common form of NVRAM today is FLASH RAM. In Flash Memory, each cell resembles a MOSFET
transistor with a control gate (CG) modulated by a floating gate (FG) interposed between the CG and the FG. The FG is surrounded by an insulating dielectric, typically an oxide. Since the FG is electrically isolated by the surrounding dielectric, any electrons placed on the FG will be trapped on the FG which screens the CG from the channel of the transistor and modifies the threshold voltage (VT) of the transistor. By writing and controlling the amount of charge placed on the FG, the FG controls the conduction state of the MOSFET FLASH device depending on the VT of the cell selected. The current flowing through the MOSFET channel is sensed to determine the state of the cell forming a binary code
where a 1 state (current flow) when an appropriate CG voltage is applied and a 0 state (no current flow) when the CG voltage is applied.
After being written to, the insulator traps electrons on the FG, locking it into the 0 state. However, in order to change that bit the insulator has to be "overcharged" to erase any charge already stored in it. This requires higher voltage, about 10 volts, much more than a battery can provide. FLASH systems include a "charge pump
" that slowly builds up power and releases it at higher voltage. This process is not only very slow, but degrades the insulators as well. For this reason FLASH has a limited lifetime, between 10,000 and 1,000,000 "writes" before the device will no longer operate effectively.
NRAM potentially avoids all of these issues. The read and write process are both "low energy" in comparison to Flash (or DRAM for that matter due to "refresh"), meaning that NRAM can result in longer battery life in conventional devices. It may also be much faster to write than either, meaning it may be used to replace both. A modern cell phone will often include FLASH memory for storing phone numbers and such, DRAM for higher performance working memory because FLASH is too slow, and additionally some SRAM in the CPU because DRAM is too slow for its own use. With NRAM all of these may be replaced, with some NRAM placed on the CPU to act as the CPU cache
, and more in other chips replacing both the DRAM and FLASH.
The only alternative memory currently ready for commercial use is ferroelectric RAM
(FRAM or FeRAM). FeRAM adds a small amount of a ferro-electric material in an otherwise "normal" DRAM cell, the state of the field in the material encoding the bit in a non-destructive format. FeRAM has all of the advantages of NRAM, although the smallest possible cell size is much larger than for NRAM. FeRAM is currently in use in a number of applications where the limited number of writes in Flash is an issue. The FeRAM read operation is inherently destructive, requiring a restoring write operation afterwards.
Other more speculative memory systems include MRAM
and PRAM
. MRAM is based on a grid of magnetic tunnel junctions. Key to MRAM's potential is the way it reads the memory using the tunnel magnetoresistive effect
, allowing it to read the memory both non-destructively and with very little power. Unfortunately, the 1st generation MRAM
, which utilized field induced writing, reached a limit in terms of size, which kept it much larger than existing Flash devices. However, two new MRAM
techniques are currently in development and hold the promises of overcoming the size limitaion and making MRAM
more competitive even with Flash memory. The techniques are Thermal Assisted Switching
(TAS), which is being developed by Crocus Technology
, and Spin Torque Transfer
(STT) on which Crocus
, Hynix
, IBM
, and several other companies are working.
PRAM is based on a technology similar to that in a writable CD or DVD, using a phase-change material that changes its magnetic or electrical properties instead of its optical ones. The PRAM material itself is scalable but requires a larger current source.
Due to the massive investment in FLASH factories (Semiconductor fabrication plant), no alternative memory has yet been able to replace FLASH in the marketplace.
Computer memory
In computing, memory refers to the physical devices used to store programs or data on a temporary or permanent basis for use in a computer or other digital electronic device. The term primary memory is used for the information in physical systems which are fast In computing, memory refers to the...
technology from the company Nantero
Nantero
Nantero is a technology company based in Woburn, Massachusetts dedicated to developing a new form of non-volatile RAM, which they call Nano-RAM. It was founded in 2000 by Greg Schmergel, Thomas Rueckes, and Brent M. Segal....
. It is a type of nonvolatile random access memory based on the mechanical position of carbon nanotubes deposited on a chip-like substrate. In theory, the small size of the nanotubes allows for very high density memories. Nantero also refers to it as NRAM.
Technology
The first generation Nantero NRAM technology was based on a three-terminal semiconductor deviceSemiconductor device
Semiconductor devices are electronic components that exploit the electronic properties of semiconductor materials, principally silicon, germanium, and gallium arsenide, as well as organic semiconductors. Semiconductor devices have replaced thermionic devices in most applications...
where a third terminal is used to switch the memory cell between memory states. The second generation NRAM technology is based on a two-terminal memory cell. The two-terminal cell has advantages such as a smaller cell size, better scalability to sub-20 nm nodes (see semiconductor device fabrication), and the ability to passivate the memory cell during fabrication.
Nantero's technology is based on a well-known effect that in a non-woven fabric matrix of carbon nanotubes (CNTs), crossed nanotubes can either be touching or slightly separated depending on their mechanical state. When close to each other, the carbon nanotubes come under the influence of Van der Waal's forces. Each NRAM "cell" consists of an interlinked network of CNTs located between two electrodes as illustrated in Fig. 1. The CNT fabric is located between two metal electrodes, which is defined and etched by photolithography
Photolithography
Photolithography is a process used in microfabrication to selectively remove parts of a thin film or the bulk of a substrate. It uses light to transfer a geometric pattern from a photomask to a light-sensitive chemical "photoresist", or simply "resist," on the substrate...
, and forms the NRAM cell.
The NRAM acts as a resistive non-volatile random access memory (RAM
Ram
-Animals:*Ram, an uncastrated male sheep*Ram cichlid, a species of freshwater fish endemic to Colombia and Venezuela-Military:*Battering ram*Ramming, a military tactic in which one vehicle runs into another...
) and can be placed in two or more resistive modes depending on the resistive state of the CNT fabric. When the CNTs are not in contact the resistance
Electrical resistance
The electrical resistance of an electrical element is the opposition to the passage of an electric current through that element; the inverse quantity is electrical conductance, the ease at which an electric current passes. Electrical resistance shares some conceptual parallels with the mechanical...
state of the fabric is high and represents a 0 (zero) state. When the CNTs are brought into contact, the resistance state of the fabric is low and represents a 1 state. NRAM can act as a memory because the two resistive states of the CNTs are both very stable. In the OFF or 0 state, the CNTs (or a portion of them) are not in contact and remain in a separated state due to the stiffness of the CNTs resulting in a high resistance or low current measurement state between the top and bottom electrodes. In the ON or 1 state, the CNTs (or a portion of them) are in contact and remain in a contacted state due to Van der Waals forces between the CNTs resulting in a low resistance or high current measurement state between the top and bottom electrodes.
To switch the NRAM between states, a small voltage greater than the read voltage is applied between top and bottom electrodes. If the NRAM is in the 0 state, the voltage applied will cause an electrostatic attraction between the CNTs close each other causing a SET operation. After the applied voltage is removed, the CNTs remain in an ON or low resistance state due to physical adhesion (Van der Waals force) with an activation energy
Activation energy
In chemistry, activation energy is a term introduced in 1889 by the Swedish scientist Svante Arrhenius that is defined as the energy that must be overcome in order for a chemical reaction to occur. Activation energy may also be defined as the minimum energy required to start a chemical reaction...
(Ea) of approximately 5eV. If the NRAM cell is in the 1 state, applying a voltage greater than the read voltage will generate CNT phonon excitations with sufficient energy to separate the CNT junctions. This is the phonon driven RESET operation. The CNTs remain in the OFF or high resistance state due to the high mechanical stiffness (Young's Modulus
Young's modulus
Young's modulus is a measure of the stiffness of an elastic material and is a quantity used to characterize materials. It is defined as the ratio of the uniaxial stress over the uniaxial strain in the range of stress in which Hooke's Law holds. In solid mechanics, the slope of the stress-strain...
1 TPa) with an activation energy (Ea) much greater than 5 eV. Figure 2 illustrates both states of an individual pair of CNTs involved in the switch operation. Due to the high activation energy (> 5eV) required for switching between states, the NRAM switch shows excellent resistance to outside interference like radiation and operating temperature that can erase or flip conventional memories like DRAM
Dram
Dram or DRAM may refer to:As a unit of measure:* Dram , an imperial unit of mass and volume* Armenian dram, a monetary unit* Dirham, a unit of currency in several Arab nationsOther uses:...
.
NRAMs are fabricated by depositing a uniform layer of CNTs onto a prefabricated array of drivers such as transistors as shown in Figure 1. The bottom electrode of the NRAM cell is in contact with the underlying via (electronics)
Via (electronics)
A via is a vertical electrical connection between different layers of conductors in a physical electronic circuit.- In IC :In integrated circuit design, a via is a small opening in an insulating oxide layer that allows a conductive connection between different layers. A via on an integrated circuit...
connecting the cell to the driver. The bottom electrode may be fabricated as part of the underlying via or it may be fabricated simultaneously with the NRAM cell, when the cell is photolithographically defined and etched. Before the cell is photolithographically defined and etched, the top electrode is deposited as a metal film onto the CNT layer so that the top metal electrode is patterned and etched during the definition of the NRAM cell. Following the dielectric passivation and fill of the array, the top metal electrode is exposed by etching back the overlying dielectric using a smoothing process such as CMP (Chemical-mechanical planarization
Chemical-mechanical planarization
Chemical Mechanical Polishing/Planarization is a process of smoothing surfaces with the combination of chemical and mechanical forces. It can be thought of as a hybrid of chemical etching and free abrasive polishing.-Description:...
). With the top electrode exposed, the next level of metal wiring interconnect is fabricated to complete the NRAM array. Figure 3 illustrates one of the many circuit methods that can be used to select a single cell for writing and reading. Using a cross-grid interconnect arrangement, the NRAM and driver, (the cell), forms a memory array similar to other memory arrays such as DRAM or Flash memory
Flash memory
Flash memory is a non-volatile computer storage chip that can be electrically erased and reprogrammed. It was developed from EEPROM and must be erased in fairly large blocks before these can be rewritten with new data...
. A single cell can be selected by applying the proper voltages to the word line (WL), bit line (BL), and select lines (SL) without disturbing the other cells in the array.
Advantages
NRAM has a density, at least in theory, similar to that of DRAM. DRAM consists of a number of capacitors, which are essentially two small metal plates with a thin insulator between them. NRAM is similar, with the terminals and electrodes being roughly the same size as the plates in a DRAM, the nanotubes between them being so much smaller they add nothing to the overall size. However it seems there is a minimum size at which a DRAM can be built, below which there simply not enough charge is being stored on the plates to be effectively read. NRAM appears to be limited only by the current state of the art in lithography. This means that NRAM may be able to become much denser than DRAM, meaning that it will also be less expensive. Additionally, unlike DRAM, NRAM does not require power to "refresh" it, and will retain its memory even after power is removed. Thus the power needed to write and retain the memory state of the device is much lower than DRAM, which has to build up charge on the cell plates. This means that NRAM will not only compete with DRAM in terms of cost, but will require much less power to run, and as a result also be much faster because write performance is largely determined by the total charge needed. NRAM can theoretically reach performance similar to SRAM, which is faster than DRAM but much less dense, and thus much more expensive.Compared other NVRAM ("Non-Volatile RAM") technologies, NRAM has further advantages. The most common form of NVRAM today is FLASH RAM. In Flash Memory, each cell resembles a MOSFET
MOSFET
The metal–oxide–semiconductor field-effect transistor is a transistor used for amplifying or switching electronic signals. The basic principle of this kind of transistor was first patented by Julius Edgar Lilienfeld in 1925...
transistor with a control gate (CG) modulated by a floating gate (FG) interposed between the CG and the FG. The FG is surrounded by an insulating dielectric, typically an oxide. Since the FG is electrically isolated by the surrounding dielectric, any electrons placed on the FG will be trapped on the FG which screens the CG from the channel of the transistor and modifies the threshold voltage (VT) of the transistor. By writing and controlling the amount of charge placed on the FG, the FG controls the conduction state of the MOSFET FLASH device depending on the VT of the cell selected. The current flowing through the MOSFET channel is sensed to determine the state of the cell forming a binary code
Binary code
A binary code is a way of representing text or computer processor instructions by the use of the binary number system's two-binary digits 0 and 1. This is accomplished by assigning a bit string to each particular symbol or instruction...
where a 1 state (current flow) when an appropriate CG voltage is applied and a 0 state (no current flow) when the CG voltage is applied.
After being written to, the insulator traps electrons on the FG, locking it into the 0 state. However, in order to change that bit the insulator has to be "overcharged" to erase any charge already stored in it. This requires higher voltage, about 10 volts, much more than a battery can provide. FLASH systems include a "charge pump
Charge pump
A charge pump is a kind of DC to DC converter that uses capacitors as energy storage elements to create either a higher or lower voltage power source. Charge pump circuits are capable of high efficiencies, sometimes as high as 90–95% while being electrically simple circuits.Charge pumps use some...
" that slowly builds up power and releases it at higher voltage. This process is not only very slow, but degrades the insulators as well. For this reason FLASH has a limited lifetime, between 10,000 and 1,000,000 "writes" before the device will no longer operate effectively.
NRAM potentially avoids all of these issues. The read and write process are both "low energy" in comparison to Flash (or DRAM for that matter due to "refresh"), meaning that NRAM can result in longer battery life in conventional devices. It may also be much faster to write than either, meaning it may be used to replace both. A modern cell phone will often include FLASH memory for storing phone numbers and such, DRAM for higher performance working memory because FLASH is too slow, and additionally some SRAM in the CPU because DRAM is too slow for its own use. With NRAM all of these may be replaced, with some NRAM placed on the CPU to act as the CPU cache
CPU cache
A CPU cache is a cache used by the central processing unit of a computer to reduce the average time to access memory. The cache is a smaller, faster memory which stores copies of the data from the most frequently used main memory locations...
, and more in other chips replacing both the DRAM and FLASH.
Comparison with other proposed systems
NRAM is one of a variety of new memory systems, many of which claim to be "universal" in the same fashion as NRAM – replacing everything from Flash to DRAM to SRAM.The only alternative memory currently ready for commercial use is ferroelectric RAM
Ferroelectric RAM
Ferroelectric RAM is a random-access memory similar in construction to DRAM but uses a ferroelectric layer instead of a dielectric layer to achieve non-volatility. FeRAM is one of a growing number of alternative non-volatile memory technologies that offer the same functionality as Flash memory...
(FRAM or FeRAM). FeRAM adds a small amount of a ferro-electric material in an otherwise "normal" DRAM cell, the state of the field in the material encoding the bit in a non-destructive format. FeRAM has all of the advantages of NRAM, although the smallest possible cell size is much larger than for NRAM. FeRAM is currently in use in a number of applications where the limited number of writes in Flash is an issue. The FeRAM read operation is inherently destructive, requiring a restoring write operation afterwards.
Other more speculative memory systems include MRAM
MRAM
Magnetoresistive Random-Access Memory is a non-volatile computer memory technology that has been under development since the 1990s. Continued increases in density of existing memory technologies – notably flash RAM and DRAM – kept it in a niche role in the market, but its proponents...
and PRAM
Phase-change memory
Phase-change memory is a type of non-volatile computer memory. PRAMs exploit the unique behavior of chalcogenide glass. Heat produced by the passage of an electric current switches this material between two states, crystalline and amorphous...
. MRAM is based on a grid of magnetic tunnel junctions. Key to MRAM's potential is the way it reads the memory using the tunnel magnetoresistive effect
Tunnel magnetoresistance
The Tunnel magnetoresistance is a magnetoresistive effect that occurs in magnetic tunnel junctions . This is a component consisting of two ferromagnets separated by a thin insulator. If the insulating layer is thin enough , electrons can tunnel from one ferromagnet into the other...
, allowing it to read the memory both non-destructively and with very little power. Unfortunately, the 1st generation MRAM
MRAM
Magnetoresistive Random-Access Memory is a non-volatile computer memory technology that has been under development since the 1990s. Continued increases in density of existing memory technologies – notably flash RAM and DRAM – kept it in a niche role in the market, but its proponents...
, which utilized field induced writing, reached a limit in terms of size, which kept it much larger than existing Flash devices. However, two new MRAM
MRAM
Magnetoresistive Random-Access Memory is a non-volatile computer memory technology that has been under development since the 1990s. Continued increases in density of existing memory technologies – notably flash RAM and DRAM – kept it in a niche role in the market, but its proponents...
techniques are currently in development and hold the promises of overcoming the size limitaion and making MRAM
MRAM
Magnetoresistive Random-Access Memory is a non-volatile computer memory technology that has been under development since the 1990s. Continued increases in density of existing memory technologies – notably flash RAM and DRAM – kept it in a niche role in the market, but its proponents...
more competitive even with Flash memory. The techniques are Thermal Assisted Switching
Thermal Assisted Switching
Thermal Assisted Switching, or TAS, is one of the new 2nd generation approaches to MRAM currently being developed. A few different designs have been proposed, but all rely on the idea of reducing the required switching fields by heating...
(TAS), which is being developed by Crocus Technology
Crocus Technology
Crocus Technology, founded in 2004, is a venture-capital-backed semiconductor startup company developing next generation magnetoresistive random access memory technology. The company's products originated in a Grenoble-based Spintec laboratory...
, and Spin Torque Transfer
Spin Torque Transfer
Spin-transfer torque is an effect in which the orientation of a magnetic layer in a tunnel magnetoresistance or spin valve can be modified using a spin-polarized current....
(STT) on which Crocus
Crocus Technology
Crocus Technology, founded in 2004, is a venture-capital-backed semiconductor startup company developing next generation magnetoresistive random access memory technology. The company's products originated in a Grenoble-based Spintec laboratory...
, Hynix
Hynix
Hynix Semiconductor Inc. chips and flash memory chips. Founded in 1983, Hynix is the world's second-largest memory chipmaker, the largest being Samsung Electronics. Formerly known as Hyundai Electronics, the company has manufacturing sites in Korea, the U.S., China and Taiwan...
, IBM
IBM
International Business Machines Corporation or IBM is an American multinational technology and consulting corporation headquartered in Armonk, New York, United States. IBM manufactures and sells computer hardware and software, and it offers infrastructure, hosting and consulting services in areas...
, and several other companies are working.
PRAM is based on a technology similar to that in a writable CD or DVD, using a phase-change material that changes its magnetic or electrical properties instead of its optical ones. The PRAM material itself is scalable but requires a larger current source.
Due to the massive investment in FLASH factories (Semiconductor fabrication plant), no alternative memory has yet been able to replace FLASH in the marketplace.
See also
- RAMRam-Animals:*Ram, an uncastrated male sheep*Ram cichlid, a species of freshwater fish endemic to Colombia and Venezuela-Military:*Battering ram*Ramming, a military tactic in which one vehicle runs into another...
- MRAMMRAMMagnetoresistive Random-Access Memory is a non-volatile computer memory technology that has been under development since the 1990s. Continued increases in density of existing memory technologies – notably flash RAM and DRAM – kept it in a niche role in the market, but its proponents...
- PRAMPhase-change memoryPhase-change memory is a type of non-volatile computer memory. PRAMs exploit the unique behavior of chalcogenide glass. Heat produced by the passage of an electric current switches this material between two states, crystalline and amorphous...
- FeRAMFerroelectric RAMFerroelectric RAM is a random-access memory similar in construction to DRAM but uses a ferroelectric layer instead of a dielectric layer to achieve non-volatility. FeRAM is one of a growing number of alternative non-volatile memory technologies that offer the same functionality as Flash memory...
- NCMNanocrystalB. D. Fahlman has described a nanocrystal as any nanomaterial with at least one dimension ≤ 100nm and that is singlecrystalline.-Summary:More properly, any material with a dimension of less than 1 micrometre, i.e., 1000 nanometers, should be referred to as a nanoparticle, not a nanocrystal...