Ring saw
Encyclopedia
A ring saw is a form of bandsaw where the band is rigid, rather than flexible. This requires the band to be circular, rather than the bandsaw's usual oblong
Oblong
Oblong may refer to:*Oblong, a rectangle whose length is greater than its width *Angus Oblong, American author and actor*Oblong, Illinois, a village in the United States...

 of straight runs between two (or three) guide wheels.

Ringsaw blades are abrasive
Abrasive
An abrasive is a material, often a mineral, that is used to shape or finish a workpiece through rubbing which leads to part of the workpiece being worn away...

 rather than toothed. The brittleness of this abrasive coating, and the need to avoid flexure, is why they are made as rings rather than oval bands. As the ring is a circle of constant radius, the blade is not flexed or bent in operation. The blades themselves are not usually rigid and may be bent slightly in fitting, but are not designed to be flexed as they rotate.

Abrasive sawblades, as used in ringsaws, are mostly used in the working of art glass
Art glass
Definitions of art glass can be as complex and contentious as definitions of what constitutes "art" and will inevitably include many refinements and exceptions...

. They use a steel band or ring, coated with a diamond abrasive, attached by nickel electroplating
Nickel electroplating
Nickel electroplating is a technique of electroplating a thin layer of nickel onto a metal object. The nickel layer can be decorative, provide corrosion resistance, wear resistance, or used to build-up worn or undersized parts for salvage purposes.-Overview:...

. Abrasive saws are used for a range of hard, brittle materials, such as in mineralogy
Mineralogy
Mineralogy is the study of chemistry, crystal structure, and physical properties of minerals. Specific studies within mineralogy include the processes of mineral origin and formation, classification of minerals, their geographical distribution, as well as their utilization.-History:Early writing...

. Ceramic tiles may also be sawn.

The main form of ring saw uses a ring or wire that is like a flat disk. The non-cutting side of the blade is behind of the cutting edge, so limits the depth of the cuts that may be made.This differs from the bandsaw, where the other part of the band is alongside the cutting edge, thus limits the width of cuts that may be made. Wire-saws are coated with an abrasive on all sides and so may cut in any direction. With the ring behind the cutting edge, cuts in the main direction will treat the blade (in mechanical terms) as an arch
Arch
An arch is a structure that spans a space and supports a load. Arches appeared as early as the 2nd millennium BC in Mesopotamian brick architecture and their systematic use started with the Ancient Romans who were the first to apply the technique to a wide range of structures.-Technical aspects:The...

, which is stiffer than a sideways force on a cylindrical blade. This geometry also gives a vertical cut in thick materials, although the cut must be kept straight and unlike a bandsaw, curves cannot be sawn if the material is thick. They may be used for mineralogy and slabbing.

Many makers of ringsaws offer a similar blade as a bandsaw too. The ringsaw blade in comparison may be made rigid, thus stronger and less flexible under cutting loads, giving a more accurate cut. Some make a particular feature of the ring saw's ability to cut forwards, backwards and sideways. As the bandsaw blade must be flexible enough to pass around the wheels, its blades are limited to cutting on the forward edge. The oblong bandsaw has a blade that is supported on two large wheels.The three-wheel bandsaw instead uses three small wheels. These offer limited contact and so suffer from many of the same problems as a ring saw. The interval between the two wheels is supported by blade guides immediately behind the cutting zone. Ring saws do not have the same straight run of blade, nor the opportunity to support much of the blade as with the wheels of a bandsaw. A ring saw is thus a somewhat fragile machine and excess pressure on a thin blade is likely to damage it.

Abrasive saws are often water-cooled and most ring saws are designed to enable this, with water pumps or drip feeds, and catch trays.

Concrete ring saws

Concrete and masonry-cutting 'ring' saws are a form of disk cutter and are unrelated to bandsaws. They do however also use a diamond abrasive.
The source of this article is wikipedia, the free encyclopedia.  The text of this article is licensed under the GFDL.
 
x
OK