Mesh (scale)
Encyclopedia
Mesh
Mesh
Mesh consists of semi-permeable barrier made of connected strands of metal, fiber, or other flexible/ductile material. Mesh is similar to web or net in that it has many attached or woven strands.-Types of mesh:...

 material is often used in determining the particle size distribution
Particle size distribution
The particle-size distribution of a powder, or granular material, or particles dispersed in fluid, is a list of values or a mathematical function that defines the relative amounts of particles present, sorted according to size...

 of a granular material
Granular material
A granular material is a conglomeration of discrete solid, macroscopic particles characterized by a loss of energy whenever the particles interact . The constituents that compose granular material must be large enough such that they are not subject to thermal motion fluctuations...

. For example, a sample from a truckload of peanuts may be placed atop a mesh with 5 mm openings. When the mesh is shaken, small broken pieces and dust pass through the mesh while whole peanuts are retained on the mesh. A commercial peanut buyer might use a test like this to determine if a batch of peanuts has too many broken pieces. This type of test is common in some industries, and to facilitate uniform testing methods, several standardized mesh series have been established.

Applicable standard
International standard
International standards are standards developed by international standards organizations. International standards are available for consideration and use, worldwide...

s are ISO 565 (1987), ISO 3310 (1999), ASTM E 11-70 (1995), DIN 4188 (1977), BS 410 (1986) and AFNOR NFX11-501 (1987).

Tyler mesh size

One well-known mesh series is the Tyler Equivalent created by the W.S. Tyler screening company. Tyler mesh size is the number of openings per (linear) inch of mesh. To calculate the size of the openings in a mesh the thickness of the wire
Wire
A wire is a single, usually cylindrical, flexible strand or rod of metal. Wires are used to bear mechanical loads and to carry electricity and telecommunications signals. Wire is commonly formed by drawing the metal through a hole in a die or draw plate. Standard sizes are determined by various...

s making up the mesh material must be taken into account. In practice, mesh openings are determined referring to a chart like the one below. Mesh size given as 4x4 means the number of squares in one inch horizontally is 4 and vertically is 4.

Variation in mesh openings

Some standards use the mesh designation as the number of wires rather than the size of openings (see Tyler, above). There can be significant differences in particle size passing small laboratory screens versus large heavy-duty industrial screens due to the different wire sizes used. Thicker wire results in a smaller opening size for an equivalent mesh. An example of variation moving between machine sizes is:
Laboratory sieve cloth
Sieve Designation Wire width Opening
[mm] [inches] [mm] [inches]
10 Mesh U.S. Std. No. 12 0.800 0.0315 1.7 0.0669 (0.0661 nominal)

Medium industrial screen cloth
Sieve Wire Width Opening Opening
10 Mesh 0.035 in 0.0650 in 1651 μm

Heavy industrial screen cloth
Sieve Wire Width Opening Opening
10 Mesh 0.047 in 0.053 in 1346 μm

Particle size distribution

Powders and granular materials are sometimes described as having a certain mesh size (e.g. 30 mesh sand). By itself, this type of description is somewhat ambiguous. More precise specifications will indicate that a material will pass through some specific mesh (that is, have a maximum size; larger pieces won't fit through this mesh) but will be retained by some specific tighter mesh (that is, a minimum size; pieces smaller than this will have passed through the mesh). This type of description establishes a range of particle sizes.

One notation for indicating particle size distribution using mesh size is to use + and - designations. A "+" before the sieve mesh indicates the particles are retained by the sieve, while a "-" before the sieve mesh indicates the particles pass through the sieve. This means that typically 90% or more of the particles will have mesh sizes between the two values.

For instance, if the particle size of a material is described as -80/+170 (or could also be written -80 +170), then 90% or more of the material will pass through an 80 mesh sieve and be retained by a 170 mesh sieve. Using the conversion chart below, the resulting particles will have a range of diameters between 0.089 and 0.178 mm (89 and 178 micrometers).

Abrasives

The Federation of European Producers of Abrasives (FEPA) has four sets of standards to denote size of grains coupled with the type of abrasive
Abrasive
An abrasive is a material, often a mineral, that is used to shape or finish a workpiece through rubbing which leads to part of the workpiece being worn away...

. The standards indicate a range of grit sizes that may come within any single designator which consists of a letter (F for bonded abrasives and P for coated abrasive
Coated abrasive
A coated abrasive is an abrasive grain bonded to a flexible substrate using adhesives. Common substrates are paper, cloth, vulcanized fiber, and plastic films and come in grit sizes range from very coarse to ultrafine...

s) and a number. Within each series are two standards detailing the larger macrogrit (approximately 12 – 240) and smaller microgrit (approximately 230 – 2000 or 2500) sizes and the different process by which sizes are determined (sieving for the larger grits and sedimentation for the smaller).

While following the common practice of smaller designators meaning coarser grits and similar cut-off marks between macro- and microgrit standards, the F and P series are not compatible. While F 12 and P 12 are only about 3% different in size, P 2000 is more than 750% larger than F 2000 (that is, the particles in P 2000 are about 8.5 times as large as those in F 2000).

Metal surfaces mechanically polished
Metal polishing
Polishing and buffing are finishing processes for smoothing a workpiece's surface using an abrasive and a work wheel. Technically polishing refers to processes that use an abrasive that is glued to the work wheel, while buffing uses a loose abrasive applied to the work wheel...

 are designated as having a mechanical finish related to the abrasive used.

Sieve sizing and conversion charts

Typical openings in laboratory sieve series
Sieve size (mm) BSS Tyler (approx) US (approx)
4.75 - 4 4
3.35 5 6 6
2.81 6 7 7
2.38 7 8 8
2.00 8 9 10
1.68 10 10 12
1.40 12 12 14
1.20 14 14 16
1.00 16 16 18
0.853 18 20 20
0.710 22 24 25
0.599 25 28 30
0.500 30 32 35
0.422 36 35 40
0.354 44 42 45
0.297 52 48 50
0.251 60 60 60
0.211 72 65 70
0.178 85 80 80
0.152 100 100 100
0.125 120 115 120
0.104 150 150 140
0.089 170 170 170
0.075 200 200 200
0.066 240 250 230
0.053 300 270 270
0.044 350 325 325
0.037 440 400 400


In addition to standard U.S. and Tyler mesh sizes, commercial sieves in the U.S. can also utilize three other standards. Market Grade sieves use thicker wire than other commercial grades, and so they are commonly used for applications where mesh strength (and therefore screen life) is important. Mill Grade sieves use a thinner wire diameter, which provide more open area for a given mesh size. Therefore, Mill Grade sieves are used when throughput is more important than durability. Tensile Bolting Cloth uses very fine wire diameters, and thus provides the highest fraction of open area of all sieve types; it is often used for fine sifting and screen printing.
Commercial Sieve Mesh Dimensions
Sieve size Opening Standard Mesh Tensile Bolting Cloth Mill Grade Market Grade
(mm) (in) US Tyler Mesh Opening Wire Mesh Opening Wire Mesh Opening Wire
11.2 .438 7/16” - - - - 2 .466 .054 2 .437 .063
6.3 .250 1/4” - - - - 3 .292 .041 3 .279 .054
5.6 .223 3.5 3.5 - - - 4 .215 .035 4 .2023 .0475
4.75 .187 4 4 - - - - - - 4 .187 .063
4.0 .157 5 5 - - - 5 .168 .032 5 .159 .041
3.35 .132 6 6 - - - 6 .139 .028 6 .132 .0348
2.80 .110 7 7 - - - 7 .115 .028 7 .108 .035
2.36 .0937 8 8 - - - 8 .100 .025 8 .0964 .0286
2.0 .0787 10 9 - - - 9 .088 .023 10 .0742 .0258
1.85 - - - - - - 10 .080 .020 11 .073 .018
1.7 .0661 12 10 14 .062 .009 12 .065 .018 12 .0603 .023
1.4 .0555 14 12 16 .0535 .009 14 .054 .017 14 .051 .0204
1.18 .0469 16 14 18 .0466 .009 16 .0465 .016 16 .0445 .0181
1.04 - - - 20 .0410 .009 - - - - - -
1.0 .0394 18 16 22 .0380 .0075 18 .0406 .015 18 .0386 .0173
.85 .0331 20 20 24 .0342 .0075 20 .0360 .014 20 .034 .0162
.787 - - - 26 .0310 .0075 22 .0320 .0135 - - -
.71 .0278 25 24 28 .0282 .0075 24 .0287 .013 24 .0277 .014
.681 - - - 30 .0268 .0065 26 .0275 .011 - - -
.63 - - - 32 .0248 .0065 28 .0275 .010 - - -
.60 .0234 30 28 34 .0229 .0065 30 .0238 .0095 - - -
.541 - - - 36 .0213 .0065 32 .0223 .009 - - -
.50 .0197 35 32 38 .0198 .0065 34 .0204 .009 30 .0203 .0128
.47 - - - 40 .0185 .0065 36 .0188 .009 - - -
.465 - - - 42 .0183 .0055 38 .0178 .0085 - - -
.437 - - - 44 .0172 .0055 - - - 35 .0176 .0118
.425 .0165 40 35 46 .0162 .0055 40 .0165 .0085 - - -
.389 - - - 48 .0153 .0055 - - - 40 .0150 .0104
.368 - - - 50 .0145 .0055 - - - - - -
.355 .0139 45 42 52 .0137 .0055 45 .0142 .008 - - -
.33 - - - 54 .0130 .0055 - - - - - -
.323 - - - 58 .0127 .0045 - - - - - -
.31 - - - 60 .0122 .0045 50 .0125 .0075 - - -
.30 .0117 50 48 62 .0116 .0045 55 .0112 .007 - - -
.282 - - - 64 .0111 .0045 - - - 50 .0110 .0090
.27 - - - 70 .0106 .0037 - - - - - -
.26 - - - 72 .0102 .0037 - - - - - -
.25 .0098 60 60 74 .0098 .0037 60 .0102 .0065 - - -
.241 - - - 76 .0095 .0037 - - - - - -
.231 - - - 78 .0091 .0037 - - - 60 .0092 .0075
.224 - - - 80 .0088 .0037 - - - - - -
.212 .0083 70 65 84 .0084 .0035 - - - - - -
.20 - - - 88 .0079 .0035 - - - - - -
.193 - - - 90 .0076 .0035 - - - - - -
.18 .0070 80 80 94 .0071 .0035 - - - 80 .0070 .0055
.165 - - - 105 .0065 .0030 - - - - - -
.15 .0059 100 100 120 .0058 .0025 - - - 100 .0055 .0045
.125 .0049 120 115 145 .0047 .0022 - - - 120 .0046 .0037
.106 .0041 140 150 165 .0042 .0019 - - - 150 .0041 .0026
.090 .0035 170 170 200 .0034 .0016 - - - 180 .0033 .0023
.075 .0029 200 200 230 .0029 .0014 - - - 200 .0029 .0021
.063 .0025 230 250 - - - - - - 250 .0024 .0016
.053 .0021 270 270 300 .0021 .0012 - - - 270 .0021 .0016
.045 .0017 325 325 - - - - - - 325 .0017 .0014
.038 .0015 400 400 - - - - - - 400 .0015 .0010
.025 .0010 500 - - - - - - - 500 .0010 .0010
.020 .0008 632 - - - - - - - 635 .0008 .0008


Further information on equivalent mesh sizes from 5μm to 25.4mm is available Available sieve sizes are usually regulated by standards. Those in common use are ISO 565:1990 and ISO 3310-1:2000 (international), EN 933-1(European) and ASTM E11:01 (US). EN standards are available with national 'badging' so appear as BS EN, FR EN, DE EN, etc.

Although such information contains long lists of sieve sizes, in practice sieves are normally used in series in which each member sieve is selected to pass particles approximately 1/√2 or 1/2 smaller in size than the previous sieve. For example the series 80mm, 63, 40, 31.5, 20, 16, 14, 10, 8, 6.3, 4, 2.8, 2mm is routinely available in many European countries or the series with the larger steps 63, 31.5, 16, 8, 4, 2, 1mm, 500μm, 250, 125, 63μm is commonly used to grade aggregates in the construction industry. Such series are somewhat derived from the principles originally established by Renard and now known as Renard series. Some users replace some of those indicated above with 45, 22.4, 12.5, 11.2 and 5.6mm sieves, mostly because of historical usage of such sizes in their country or industry.

External links

The source of this article is wikipedia, the free encyclopedia.  The text of this article is licensed under the GFDL.
 
x
OK