Link adaptation
Encyclopedia
Link adaptation, or adaptive coding and modulation (ACM), is a term used in wireless communications to denote the matching of the modulation
Modulation
In electronics and telecommunications, modulation is the process of varying one or more properties of a high-frequency periodic waveform, called the carrier signal, with a modulating signal which typically contains information to be transmitted...

, coding
Coding
Coding may refer to:* Channel coding in coding theory* Line coding* Computer programming, the process of designing, writing, testing, debugging / troubleshooting, and maintaining the source code of computer programs...

 and other signal and protocol
Communications protocol
A communications protocol is a system of digital message formats and rules for exchanging those messages in or between computing systems and in telecommunications...

 parameters to the conditions on the radio link (e.g. the pathloss, the interference
Interference (communication)
In communications and electronics, especially in telecommunications, interference is anything which alters, modifies, or disrupts a signal as it travels along a channel between a source and a receiver. The term typically refers to the addition of unwanted signals to a useful signal...

 due to signals coming from other transmitters, the sensitivity of the receiver, the available transmitter power margin, etc.). For example, EDGE
Enhanced Data Rates for GSM Evolution
Enhanced Data rates for GSM Evolution is a digital mobile phone technology that allows improved data transmission rates as a backward-compatible extension of GSM...

 uses a rate adaptation algorithm that adapts the modulation and coding scheme (MCS) according to the quality of the radio channel, and thus the bit rate and robustness of data transmission. The process of link adaptation is a dynamic one and the signal and protocol parameters change as the radio link conditions change -- for example in HSDPA in UMTS this can take place every 2 ms.

Adaptive modulation systems invariably require some channel state information
Channel state information
In wireless communications, channel state information refers to known channel properties of a communication link. This information describes how a signal propagates from the transmitter to the receiver and represents the combined effect of, for example, scattering, fading, and power decay with...

 at the transmitter. This could be acquired in time division duplex systems by assuming the channel from the transmitter to the receiver
Receiver (Information Theory)
The receiver in information theory is the receiving end of a communication channel. It receives decoded messages/information from the sender, who first encoded them. Sometimes the receiver is modeled so as to include the decoder. Real-world receivers like radio receivers or telephones can not be...

 is approximately the same as the channel from the receiver to the transmitter. Alternatively, the channel knowledge can also be directly measured at the receiver, and fed back to the transmitter. Adaptive modulation systems improve rate of transmission, and/or bit error rates, by exploiting the channel state information
Channel state information
In wireless communications, channel state information refers to known channel properties of a communication link. This information describes how a signal propagates from the transmitter to the receiver and represents the combined effect of, for example, scattering, fading, and power decay with...

 that is present at the transmitter. Especially over fading channels which model wireless
Wireless
Wireless telecommunications is the transfer of information between two or more points that are not physically connected. Distances can be short, such as a few meters for television remote control, or as far as thousands or even millions of kilometers for deep-space radio communications...

 propagation environments, adaptive modulation systems exhibit great performance enhancements compared to systems that do not exploit channel knowledge at the transmitter.

Example

In HSDPA link adaptation is performed by:
  • choice of modulation type -- the link can employ QPSK for noisy channels and 16QAM
    Quadrature amplitude modulation
    Quadrature amplitude modulation is both an analog and a digital modulation scheme. It conveys two analog message signals, or two digital bit streams, by changing the amplitudes of two carrier waves, using the amplitude-shift keying digital modulation scheme or amplitude modulation analog...

     for clearer channels. The former is more robust and can tolerate higher levels of interference but has lower transmission bit rate
    Bit rate
    In telecommunications and computing, bit rate is the number of bits that are conveyed or processed per unit of time....

    . The latter has twice higher bit rate but is more prone to errors due to interference and noise hence it requires stronger FEC (forward error correction
    Forward error correction
    In telecommunication, information theory, and coding theory, forward error correction or channel coding is a technique used for controlling errors in data transmission over unreliable or noisy communication channels....

    ) coding which in turn means more redundant bits and lower information bit rate;
  • choice of FEC code rate
    Code rate
    In telecommunication and information theory, the code rate of a forward error correction code is the proportion of the data-stream that is useful...

     -- the FEC code used has a rate of 1/3, but it can be varied effectively by bit puncturing
    Puncturing
    In coding theory, puncturing is the process of removing some of the parity bits after encoding with an error-correction code. This has the same effect as encoding with an error-correction code with a higher rate, or less redundancy...

    and HARQ with incremental redundancy. When the radio link conditions are good more bits are punctured and the information bit rate is increased. In poor link conditions all redundant bits are transmitted and the information bit rate drops. In very bad link conditions retransmissions occur due to HARQ which ensure correct reception of the sent information but further slow down the bit rate.


Thus HSDPA adapts to achieve very high bit rates, of the order of 14 megabit/s, on clear channels using 16-QAM and close to 1/1 coding rate. On noisy channels HSDPA adapts to provide reliable communications using QPSK and 1/3 coding rate but the information bit rate drops to about 2.4 megabit/s. This adaptation is performed up to 500 times per second.
The source of this article is wikipedia, the free encyclopedia.  The text of this article is licensed under the GFDL.
 
x
OK