6mm Lee Navy
Encyclopedia
The 6mm Lee Navy aka 6mm U.S.N. is an obsolete American
rifle
cartridge
. It was the service cartridge of the United States Navy and Marine Corps from 1895, officially replacing the .45-70
Government round, and was the first small-bore high-velocity smokeless powder cartridge to be adopted by either service. The 6mm Lee Navy was in turn replaced by the .30 Army
(.30-40 Krag) cartridge in 1899.
As the Chief of the Bureau of Naval Ordnance stated in his 1897 Small Arms report to the Secretary of the Navy: "In making what may appear a radical departure in its selection of a caliber smaller than as yet adopted elsewhere...the Bureau is convinced it is looking to the future...it is surely wise to attempt to advance with one stride as far as existing conditions allow toward the goal to which the world is moving with slow steps." The report went on to list the advantages of the smaller 6mm caliber: greatly increased velocity, flatness of bullet trajectory, reduced recoil, a 100% increase in penetration compared to the former .45-70 Government cartridge, and the ability to carry twice the number of cartridges per individual sailor or marine. However, the report acknowledged the 6mm round had two principal disadvantages: first, that as a small-caliber round, the 6mm bullet would not sufficiently wound an enemy to put him out of action, and second, the "shock" or stopping power of the smaller bullet would not "stop the onset of excited men at short range." In answer to these objections, the report gave three responses: first, "the battle of the future will be fought at long range, and men will not live to come to close quarters with an enemy who stands his ground"; second, 99% of wounded enemy soldiers would not likely investigate the severity of their wound, but simply retire to the rear; third, the explosive effect of a small-caliber, high-velocity bullet against the human body, whereby the bullet tumbled or fragmented to produce devastating wounds against bone or fluid-filled organs, would be more incapacitating at all ranges than wounds made by a slow-moving bullet of large caliber.
On August 1, 1894 a naval test board was convened at the Naval Torpedo Station
in Newport, Rhode Island
to test submitted magazine rifles in the new 6mm Navy caliber developed by naval ordnance authorities; according to the government notice of bid requirements, no other calibers or cartridges were to be considered. Winchester made the ammunition for the government, which in turn provided each competitor with 6mm U.S.N. cartridges and 0.236-inch caliber rifle barrels, the latter supplied unchambered and with receiver threads uncut. The rifle action was required to withstand the firing of five overpressure (proof) cartridges with a chamber pressure of 60,000 psi. Several inventors and rifle manufacturers submitted models for test, among them James Paris Lee
, who offered two designs, a turnbolt and a cam-action or locking bolt type, the Lee straight-pull. The Lee straight-pull was chosen as the winner in repeated trials and adopted by the U.S. Navy in 1895 as the Lee Rifle, Model of 1895, caliber 6-mm
.
As adopted by the Navy after tests at the Naval Torpedo Station, the "Ball Cartridge, 6mm" or 6mm U.S.N. cartridge featured a long bottlenecked semi-rimmed brass case and a 135 gr round-nosed, cupro-nickel coated, steel-jacketed lead-core bullet. The rifle powder for the new cartridge was Rifleite, a flake nitrocellulose smokeless powder originally developed for use in the British .303 cartridge.
The new 6mm cartridge achieved a muzzle velocity of 2,550 fps (777 m/s) and was initially manufactured by Winchester
(WRA) for the Navy. Because of production delays and the desire to have a secondary ammunition source in the event of war or other emergency, the Union Metallic Cartridge (UMC) Company was also awarded a contract to produce 6mm ammunition. After the adoption of the M1895 Lee, the case rim of the government cartridge was redesigned with a slight bevel for optimum performance in the en bloc charger-loaded magazine of the M1895 rifle; the revised cartridge was designated the 6mm U.S.N., but continued to be referred to in naval stores reports as the Ball Cartridge, 6mm. Owing to difficulties in obtaining acceptable lots of Rifleite smokeless powder for the cartridge, as well as cartridge clips, the initial April 1896 Navy order of 1,000,000 cartridges was not filled by Winchester and UMC for over a year.
In March 1897, after reports of excessive chamber pressures and short barrel life (3,000 rounds) despite the use of 4.5 per cent nickel-steel barrels, the specifications for the 6mm round were changed to incorporate a 112 gr round-nosed lead-core bullet with a copper jacket, which was then tin-plated to prevent corrosion from salt air. Winchester and UMC had difficulty in achieving the pressure limit specification (43,000 psi) for the new loading with Rifleite, and chamber pressures varied widely from lot to lot of powder, ranging up to 60,000 psi. The new M1895 Colt-Browning machine gun
was also modified to accept the new 112 gr loading the same year, and a further 500,000 cartridges were ordered to accommodate machine-gun usage.
Firing a 112 gr bullet at 2560 ft/s (780.3 m/s) from a 28 in (711.2 mm) barrel, the 6mm U.S.N. was the highest-velocity cartridge used by any military force at the time of its adoption. Designed to achieve better penetration than the Army's .30 Army cartridge used in the Model 1892/98 (Krag) rifle, the round was intended to perforate the hulls of small enemy craft such as patrol and torpedo boats, and could penetrate 13 in (330.2 mm) of soft wood at 700 yd (640.1 m), 0.5 in (12.7 mm) of low-carbon steel at 10 feet (3 m); 0.375-inch (9.5 mm) of ordinary boiler plate at 100 ft (30.5 m), or a 0.276 in (7 mm)-thick suspended chrome steel alloy boiler plate at 150 ft (45.7 m). The 112 gr roundnosed bullet had a flatter trajectory than its 135 gr predecessor at all ranges up to 500 yards; above this distance, the heavier bullet began to show an advantage. The new loading had an effective range (individual rifle fire) of around 600-700 yards, at which point the blunt-tip bullet rapidly lost velocity and energy. The 112 gr bullet, like its predecessor, demonstrated an inclination to instability unless rapidly rotated; the M1895 Lee rifle was therefore given a rapid barrel rifling twist of one turn in 7.5 inches (19 cm) (with right-hand twist) to keep the bullet from wobbling or tumbling at extended ranges. At some point, this rifling was changed in later production rifles to one turn in 10 inches RH (25 cm). Contemporary medical reports of the day noted the 112 gr bullet produced noticeably greater damage to tissue and bone than other military cartridges of the day when fired at full velocity (2,560 fps), and the bullet's copper jacket frequently fragmented or detached entirely from its lead core after penetrating a hard substance such as bone or metal.. On the other hand, when the 6mm bullet struck muscle or air-filled cavities such as the lungs, the bullet tended to make a perforating wound of small diameter that caused little damage.
The 6mm Lee Navy cartridge proved expensive to produce, with per-round cost approximately double that of the previous .45-70 service cartridge. Delays caused by difficulties in getting smokeless powder of the proper specification delayed shipments of ammunition under the Navy's contract with Winchester (WRA) and UMC, and shipments of the 6mm Lee rifle were also delayed due to manufacturing issues and contract changes. As a result, the .45-70 government cartridge and small arms chambered for it continued in front-line service with the Navy until 1897, when the latter cartridge was made substitute standard for second-line vessels. Because of arguments over inadequate congressional appropriations, Marine battalions scheduled to be equipped with the Lee had not received either rifles or ammunition until 1897, two years after adoption of the cartridge and rifle. Colonel-Commandant Charles Heywood
of the Marine Corps reportedly refused initial deliveries of small numbers of Lee rifles to Marine battalions until he received assurances that an appropriation would be made to the Corps for at least 3,000 Lee rifles, improved target ranges, and enough ammunition to continue existing marksmanship training programs. Despite this threat, the report of the Marine Corps Quartermaster as of September 1897 begged the Secretary for an additional $10,000 appropriation for 6mm ammunition to allow Marines to conduct live fire and target practice with the Lee rifle. The report went on to warn that, except for drill practice, enlisted Marines were "entirely unfamiliar with the use of this arm", since all target practice had to be conducted using the old single-shot Springfield and .45-70 ammunition.
Issued to both naval armed guards (bluejackets) and Marine battalions, the 6mm Lee Navy cartridge saw combat service with U.S. forces (primarily Marine riflemen and machine-gun teams) in both Cuba and the Philippines during the Spanish-American War
, and was also issued to small formations of attached Cuban rebels participating in the Guantánamo Bay campaign. The lighter weight of the 6mm Lee cartridge meant individual riflemen could carry more cartridges, since 160 .30 Army cartridges weighed as much as 220 rounds of 6mm.
During the fighting to secure Guantánamo Bay harbor in Cuba, the light weight of the 6mm Lee Navy cartridge enabled individual Marines to carry extra ammunition without an undue weight penalty, an advantage when pursuing an enemy over mountainous and difficult ground. The extra cartridges proved useful when early ammunition resupply from Navy ships was disrupted at the outset of the Guantanamo operation, allowing Marines to continue their assault even while individually resupplying Cuban rebels who had run short of ammunition.
Later, during the early stages of the Moro Rebellion
in the Philippines, the 6mm round was criticized by some Marines for failing to stop the frenzied charges of bolo-wielding Moro juramentados at very close ranges. The possibility a 6mm bullet might lack shocking power (stopping power) had been raised as far back as 1895 when the cartridge was in the process of being developed for adoption. On the other hand, the Marine Legation Guard, which used the 6mm Lee in the defense of the foreign legations in Peking during the Boxer Rebellion
of 1900, together with marines and navy bluejackets serving in the expedition relieving the besieged legations, apparently had no such criticisms.
However, the high velocity 6mm round was ahead of its time in terms of powder technology and barrel steel metallurgy. In addition to complaints of bore fouling with corrosive nitro-compounds M1895 rifles in service began to display signs of early barrel wear and throat erosion caused by inconsistent chamber pressures and powder burn rates, despite the Navy's requirement of nickel-steel barrels.
Several factors led to the discontinuance of the 6mm Lee as an official U.S. military cartridge. The most important was the decision of the War Department, based upon a recommendation by a board composed of Army, Navy, and Marine Corps officers, to standardize on the .30 Army cartridge for all services. Finally, the 6mm's special semi-rimless beveled-rim case was designed to work optimally in the charger clips of the M1895 rifle, which proved an unnecessary complication when adapting the cartridge to other, more modern machine guns and small arms. Aside from the benefits of interchangeability between the services, the board noted the government had its greatest investment in the .30 Army cartridge and rifles chambered for it. Nevertheless, the board acknowledged the rimmed .30 Army round was less than ideal when used in modern machine guns, and the decision to adopt the it for the Navy and Marine Corps might be postponed until a rimless version was developed (which would eventually take place in 1903 in the form of the .30-03
).
The 6mm Lee was adopted prior to the invention of the spitzer
bullet; the light roundnosed 6mm bullet lost much of its effectiveness at 600-700 yards, while the 220 gr roundnosed bullet of the .30 Army service cartridge was still considered effective at ranges of 1,000 yards or more, an important consideration in the days when rifle and indirect
machine gun fire at distant targets such as massed enemy infantry was considered necessary. While by no means a universal opinion, the lack of shocking power of the 6mm Lee reported by some Marine units in combat may have weighed against the idea of delaying a change to the .30 Army for all services. A further complication was that issues of barrel wear from the Rifleite smokeless powder and corrosive primer used in the 6mm cartridge continued to plague Navy ordnance authorities. Finally, due in part to its long, thick-gauged semi-rimless rim case and beveled rim, the 6mm Lee was one of the most expensive service cartridges to produce in terms of cost per round, yet it was already becoming obsolescent in comparison to ammunition utilizing more efficient powders and true rimless cases. Rapid developments in military small arms ammunition would soon demonstrate the advantages of a magazine-fed rifle and machine gun cartridge with a rimless case and spitzer bullet, features not found in either the .30 Army or the 6mm Lee.
In 1899, the Navy officially adopted the .30 Army cartridge for all small arms, though it continued to use the 6mm for existing stocks of Lee rifles and Colt machine guns. In 1907, the Navy adopted the .30-'06 Springfield
cartridge for both rifles and machine guns. 6mm Lee ammunition still in military stores in 1917 was sold at auction by the government to a private military surplus dealer, F.W. Bannerman; the powder used in the government cartridges had deteriorated to such a degree they were determined to be unfit for use by Bannerman, who destroyed the entire lot rather than resell them.
, which used a necked-down 6mm Lee case with a .22-caliber bullet.
United States
The United States of America is a federal constitutional republic comprising fifty states and a federal district...
rifle
Rifle
A rifle is a firearm designed to be fired from the shoulder, with a barrel that has a helical groove or pattern of grooves cut into the barrel walls. The raised areas of the rifling are called "lands," which make contact with the projectile , imparting spin around an axis corresponding to the...
cartridge
Cartridge (firearms)
A cartridge, also called a round, packages the bullet, gunpowder and primer into a single metallic case precisely made to fit the firing chamber of a firearm. The primer is a small charge of impact-sensitive chemical that may be located at the center of the case head or at its rim . Electrically...
. It was the service cartridge of the United States Navy and Marine Corps from 1895, officially replacing the .45-70
.45-70
The .45-70 rifle cartridge, also known as .45-70 Government, was developed at the U.S. Army's Springfield Armory for use in the Springfield Model 1873...
Government round, and was the first small-bore high-velocity smokeless powder cartridge to be adopted by either service. The 6mm Lee Navy was in turn replaced by the .30 Army
.30-40 Krag
The .30-40 Krag was a cartridge developed in the early 1890s to provide the U.S. armed forces with a smokeless powder cartridge suited for use with modern small-bore repeating rifles to be selected in the 1892 small arm trials...
(.30-40 Krag) cartridge in 1899.
History and development
By 1894, the U.S. Navy desired to adopt a modern small-bore, smokeless powder service cartridge and rifle in keeping with other first-line naval powers for both naval and marine forces. Naval authorities decided that the new cartridge should be adaptable to both rifles and machine guns. Noting that the world's military forces were adopting smaller and smaller caliber rifles with higher velocity cartridges, U.S. naval authorities decided to leapfrog the trend to smaller and smaller calibers by adopting a cartridge in 6mm (0.236 inch) caliber, with a case capable of holding up to 40 gr of 'rifleite' smokeless powder and proof chamber pressures of up to 60,000 psi. While the government cartridge was being developed, the Navy tested rifle barrels in various alloys and rifling twists, eventually settling on a barrel steel made of 4.5 per cent nickel steel, with a rifling twist of one turn in 6.5 inches.As the Chief of the Bureau of Naval Ordnance stated in his 1897 Small Arms report to the Secretary of the Navy: "In making what may appear a radical departure in its selection of a caliber smaller than as yet adopted elsewhere...the Bureau is convinced it is looking to the future...it is surely wise to attempt to advance with one stride as far as existing conditions allow toward the goal to which the world is moving with slow steps." The report went on to list the advantages of the smaller 6mm caliber: greatly increased velocity, flatness of bullet trajectory, reduced recoil, a 100% increase in penetration compared to the former .45-70 Government cartridge, and the ability to carry twice the number of cartridges per individual sailor or marine. However, the report acknowledged the 6mm round had two principal disadvantages: first, that as a small-caliber round, the 6mm bullet would not sufficiently wound an enemy to put him out of action, and second, the "shock" or stopping power of the smaller bullet would not "stop the onset of excited men at short range." In answer to these objections, the report gave three responses: first, "the battle of the future will be fought at long range, and men will not live to come to close quarters with an enemy who stands his ground"; second, 99% of wounded enemy soldiers would not likely investigate the severity of their wound, but simply retire to the rear; third, the explosive effect of a small-caliber, high-velocity bullet against the human body, whereby the bullet tumbled or fragmented to produce devastating wounds against bone or fluid-filled organs, would be more incapacitating at all ranges than wounds made by a slow-moving bullet of large caliber.
On August 1, 1894 a naval test board was convened at the Naval Torpedo Station
Naval Undersea Warfare Center
The Naval Undersea Warfare Center is the United States Navy's full-spectrum research, development, test and evaluation, engineering and fleet support center for submarines, autonomous underwater systems, and offensive and defensive weapons systems associated with undersea warfare...
in Newport, Rhode Island
Newport, Rhode Island
Newport is a city on Aquidneck Island in Newport County, Rhode Island, United States, about south of Providence. Known as a New England summer resort and for the famous Newport Mansions, it is the home of Salve Regina University and Naval Station Newport which houses the United States Naval War...
to test submitted magazine rifles in the new 6mm Navy caliber developed by naval ordnance authorities; according to the government notice of bid requirements, no other calibers or cartridges were to be considered. Winchester made the ammunition for the government, which in turn provided each competitor with 6mm U.S.N. cartridges and 0.236-inch caliber rifle barrels, the latter supplied unchambered and with receiver threads uncut. The rifle action was required to withstand the firing of five overpressure (proof) cartridges with a chamber pressure of 60,000 psi. Several inventors and rifle manufacturers submitted models for test, among them James Paris Lee
James Paris Lee
James Paris Lee was a Scottish-Canadian and later American inventor and arms designer, best known for inventing the bolt action that led to the Lee-Metford and Lee-Enfield series of rifles.-Early Life and Career:...
, who offered two designs, a turnbolt and a cam-action or locking bolt type, the Lee straight-pull. The Lee straight-pull was chosen as the winner in repeated trials and adopted by the U.S. Navy in 1895 as the Lee Rifle, Model of 1895, caliber 6-mm
M1895 Lee Navy
The Lee Model 1895 was a straight-pull, cam-action magazine rifle adopted in limited numbers by the U.S. Navy and Marine Corps in 1895 as a first-line infantry rifle...
.
As adopted by the Navy after tests at the Naval Torpedo Station, the "Ball Cartridge, 6mm" or 6mm U.S.N. cartridge featured a long bottlenecked semi-rimmed brass case and a 135 gr round-nosed, cupro-nickel coated, steel-jacketed lead-core bullet. The rifle powder for the new cartridge was Rifleite, a flake nitrocellulose smokeless powder originally developed for use in the British .303 cartridge.
The new 6mm cartridge achieved a muzzle velocity of 2,550 fps (777 m/s) and was initially manufactured by Winchester
Winchester Repeating Arms Company
The Winchester Repeating Arms Company was a prominent American maker of repeating firearms, located in New Haven, Connecticut. The Winchester brand is today used under license by two subsidiaries of the Herstal Group, Fabrique Nationale of Belgium and the Browning Arms Company of Morgan, Utah.-...
(WRA) for the Navy. Because of production delays and the desire to have a secondary ammunition source in the event of war or other emergency, the Union Metallic Cartridge (UMC) Company was also awarded a contract to produce 6mm ammunition. After the adoption of the M1895 Lee, the case rim of the government cartridge was redesigned with a slight bevel for optimum performance in the en bloc charger-loaded magazine of the M1895 rifle; the revised cartridge was designated the 6mm U.S.N., but continued to be referred to in naval stores reports as the Ball Cartridge, 6mm. Owing to difficulties in obtaining acceptable lots of Rifleite smokeless powder for the cartridge, as well as cartridge clips, the initial April 1896 Navy order of 1,000,000 cartridges was not filled by Winchester and UMC for over a year.
In March 1897, after reports of excessive chamber pressures and short barrel life (3,000 rounds) despite the use of 4.5 per cent nickel-steel barrels, the specifications for the 6mm round were changed to incorporate a 112 gr round-nosed lead-core bullet with a copper jacket, which was then tin-plated to prevent corrosion from salt air. Winchester and UMC had difficulty in achieving the pressure limit specification (43,000 psi) for the new loading with Rifleite, and chamber pressures varied widely from lot to lot of powder, ranging up to 60,000 psi. The new M1895 Colt-Browning machine gun
M1895 Colt-Browning machine gun
The Colt-Browning M1895, nicknamed potato digger due to its unusual operating mechanism, is an air-cooled, belt-fed, gas-operated machine gun that fires from a closed bolt with a cyclic rate of 450 rounds per minute...
was also modified to accept the new 112 gr loading the same year, and a further 500,000 cartridges were ordered to accommodate machine-gun usage.
Firing a 112 gr bullet at 2560 ft/s (780.3 m/s) from a 28 in (711.2 mm) barrel, the 6mm U.S.N. was the highest-velocity cartridge used by any military force at the time of its adoption. Designed to achieve better penetration than the Army's .30 Army cartridge used in the Model 1892/98 (Krag) rifle, the round was intended to perforate the hulls of small enemy craft such as patrol and torpedo boats, and could penetrate 13 in (330.2 mm) of soft wood at 700 yd (640.1 m), 0.5 in (12.7 mm) of low-carbon steel at 10 feet (3 m); 0.375-inch (9.5 mm) of ordinary boiler plate at 100 ft (30.5 m), or a 0.276 in (7 mm)-thick suspended chrome steel alloy boiler plate at 150 ft (45.7 m). The 112 gr roundnosed bullet had a flatter trajectory than its 135 gr predecessor at all ranges up to 500 yards; above this distance, the heavier bullet began to show an advantage. The new loading had an effective range (individual rifle fire) of around 600-700 yards, at which point the blunt-tip bullet rapidly lost velocity and energy. The 112 gr bullet, like its predecessor, demonstrated an inclination to instability unless rapidly rotated; the M1895 Lee rifle was therefore given a rapid barrel rifling twist of one turn in 7.5 inches (19 cm) (with right-hand twist) to keep the bullet from wobbling or tumbling at extended ranges. At some point, this rifling was changed in later production rifles to one turn in 10 inches RH (25 cm). Contemporary medical reports of the day noted the 112 gr bullet produced noticeably greater damage to tissue and bone than other military cartridges of the day when fired at full velocity (2,560 fps), and the bullet's copper jacket frequently fragmented or detached entirely from its lead core after penetrating a hard substance such as bone or metal.. On the other hand, when the 6mm bullet struck muscle or air-filled cavities such as the lungs, the bullet tended to make a perforating wound of small diameter that caused little damage.
The 6mm Lee Navy cartridge proved expensive to produce, with per-round cost approximately double that of the previous .45-70 service cartridge. Delays caused by difficulties in getting smokeless powder of the proper specification delayed shipments of ammunition under the Navy's contract with Winchester (WRA) and UMC, and shipments of the 6mm Lee rifle were also delayed due to manufacturing issues and contract changes. As a result, the .45-70 government cartridge and small arms chambered for it continued in front-line service with the Navy until 1897, when the latter cartridge was made substitute standard for second-line vessels. Because of arguments over inadequate congressional appropriations, Marine battalions scheduled to be equipped with the Lee had not received either rifles or ammunition until 1897, two years after adoption of the cartridge and rifle. Colonel-Commandant Charles Heywood
Charles Heywood
Major General Charles Heywood was the ninth Commandant of the Marine Corps. He served as an officer for over 45 years and was the first Marine to reach the rank of major general...
of the Marine Corps reportedly refused initial deliveries of small numbers of Lee rifles to Marine battalions until he received assurances that an appropriation would be made to the Corps for at least 3,000 Lee rifles, improved target ranges, and enough ammunition to continue existing marksmanship training programs. Despite this threat, the report of the Marine Corps Quartermaster as of September 1897 begged the Secretary for an additional $10,000 appropriation for 6mm ammunition to allow Marines to conduct live fire and target practice with the Lee rifle. The report went on to warn that, except for drill practice, enlisted Marines were "entirely unfamiliar with the use of this arm", since all target practice had to be conducted using the old single-shot Springfield and .45-70 ammunition.
Issued to both naval armed guards (bluejackets) and Marine battalions, the 6mm Lee Navy cartridge saw combat service with U.S. forces (primarily Marine riflemen and machine-gun teams) in both Cuba and the Philippines during the Spanish-American War
Spanish-American War
The Spanish–American War was a conflict in 1898 between Spain and the United States, effectively the result of American intervention in the ongoing Cuban War of Independence...
, and was also issued to small formations of attached Cuban rebels participating in the Guantánamo Bay campaign. The lighter weight of the 6mm Lee cartridge meant individual riflemen could carry more cartridges, since 160 .30 Army cartridges weighed as much as 220 rounds of 6mm.
During the fighting to secure Guantánamo Bay harbor in Cuba, the light weight of the 6mm Lee Navy cartridge enabled individual Marines to carry extra ammunition without an undue weight penalty, an advantage when pursuing an enemy over mountainous and difficult ground. The extra cartridges proved useful when early ammunition resupply from Navy ships was disrupted at the outset of the Guantanamo operation, allowing Marines to continue their assault even while individually resupplying Cuban rebels who had run short of ammunition.
Later, during the early stages of the Moro Rebellion
Moro Rebellion
The Moro Rebellion was an armed military conflict between Moro revolutionary groups in the Mindanao, Sulu, and Palawan and the United States military which took place in the Philippines as early as between 1899 to 1913, following the Spanish-American War in 1898...
in the Philippines, the 6mm round was criticized by some Marines for failing to stop the frenzied charges of bolo-wielding Moro juramentados at very close ranges. The possibility a 6mm bullet might lack shocking power (stopping power) had been raised as far back as 1895 when the cartridge was in the process of being developed for adoption. On the other hand, the Marine Legation Guard, which used the 6mm Lee in the defense of the foreign legations in Peking during the Boxer Rebellion
Boxer Rebellion
The Boxer Rebellion, also called the Boxer Uprising by some historians or the Righteous Harmony Society Movement in northern China, was a proto-nationalist movement by the "Righteous Harmony Society" , or "Righteous Fists of Harmony" or "Society of Righteous and Harmonious Fists" , in China between...
of 1900, together with marines and navy bluejackets serving in the expedition relieving the besieged legations, apparently had no such criticisms.
However, the high velocity 6mm round was ahead of its time in terms of powder technology and barrel steel metallurgy. In addition to complaints of bore fouling with corrosive nitro-compounds M1895 rifles in service began to display signs of early barrel wear and throat erosion caused by inconsistent chamber pressures and powder burn rates, despite the Navy's requirement of nickel-steel barrels.
Several factors led to the discontinuance of the 6mm Lee as an official U.S. military cartridge. The most important was the decision of the War Department, based upon a recommendation by a board composed of Army, Navy, and Marine Corps officers, to standardize on the .30 Army cartridge for all services. Finally, the 6mm's special semi-rimless beveled-rim case was designed to work optimally in the charger clips of the M1895 rifle, which proved an unnecessary complication when adapting the cartridge to other, more modern machine guns and small arms. Aside from the benefits of interchangeability between the services, the board noted the government had its greatest investment in the .30 Army cartridge and rifles chambered for it. Nevertheless, the board acknowledged the rimmed .30 Army round was less than ideal when used in modern machine guns, and the decision to adopt the it for the Navy and Marine Corps might be postponed until a rimless version was developed (which would eventually take place in 1903 in the form of the .30-03
.30-03
The .30-03 was a short-lived cartridge developed by the United States in 1903, to replace the .30-40 Krag in the new Springfield 1903 rifle. The .30-03 was also called the .30-45, since it used a 45 grain powder charge; the name was changed to .30-03 to indicate the year of adoption. It used a...
).
The 6mm Lee was adopted prior to the invention of the spitzer
Spitzer (bullet)
A spitzer, also commonly referred to as a spire point bullet, is an aerodynamic bullet design used in most intermediate and high-powered rifle cartridges...
bullet; the light roundnosed 6mm bullet lost much of its effectiveness at 600-700 yards, while the 220 gr roundnosed bullet of the .30 Army service cartridge was still considered effective at ranges of 1,000 yards or more, an important consideration in the days when rifle and indirect
Indirect fire
Indirect fire means aiming and firing a projectile in a high trajectory without relying on a direct line of sight between the gun and its target, as in the case of direct fire...
machine gun fire at distant targets such as massed enemy infantry was considered necessary. While by no means a universal opinion, the lack of shocking power of the 6mm Lee reported by some Marine units in combat may have weighed against the idea of delaying a change to the .30 Army for all services. A further complication was that issues of barrel wear from the Rifleite smokeless powder and corrosive primer used in the 6mm cartridge continued to plague Navy ordnance authorities. Finally, due in part to its long, thick-gauged semi-rimless rim case and beveled rim, the 6mm Lee was one of the most expensive service cartridges to produce in terms of cost per round, yet it was already becoming obsolescent in comparison to ammunition utilizing more efficient powders and true rimless cases. Rapid developments in military small arms ammunition would soon demonstrate the advantages of a magazine-fed rifle and machine gun cartridge with a rimless case and spitzer bullet, features not found in either the .30 Army or the 6mm Lee.
In 1899, the Navy officially adopted the .30 Army cartridge for all small arms, though it continued to use the 6mm for existing stocks of Lee rifles and Colt machine guns. In 1907, the Navy adopted the .30-'06 Springfield
.30-06 Springfield
The .30-06 Springfield cartridge or 7.62×63mm in metric notation, was introduced to the United States Army in 1906 and standardized, and was in use until the 1960s and early 1970s. It replaced the .30-03, 6 mm Lee Navy, and .30 US Army...
cartridge for both rifles and machine guns. 6mm Lee ammunition still in military stores in 1917 was sold at auction by the government to a private military surplus dealer, F.W. Bannerman; the powder used in the government cartridges had deteriorated to such a degree they were determined to be unfit for use by Bannerman, who destroyed the entire lot rather than resell them.
Commercial and hunting use
A commercial sporting version of the M1895 Lee Straight Pull was sold by Winchester, which did not sell well in U.S. markets due to a heavy preference by American consumers for lever action rifle designs. The cartridge was chambered for a time in the Remington-Lee and Blake magazine rifles. With a reputation for penetration and explosive effect, the 6mm Lee was reportedly quite popular as a hunting cartridge in Alaska and Northwest Canada. It was discontinued from commercial production in 1935. The 6mm Lee cartridge case later served as the basis for the .220 Swift.220 Swift
The .220 Swift is a semi-rimmed rifle cartridge developed by Winchester and introduced in 1935. It was the first factory loaded rifle cartridge with a muzzle velocity of over...
, which used a necked-down 6mm Lee case with a .22-caliber bullet.
Sources
- Barnes, Frank C., ed. by John T. Amber. "6mm Lee Navy", in Cartridges of the World, pp. 73 & 123. Northfield, IL: DBI Books, 1972. ISBN 0-695-80326-3.