Ski wax
Encyclopedia
Ski wax is a material applied to the bottom of ski
s or snowboard
s to improve the ski's performance on snow. It can also be applied to other devices that slide over snow and ice such as toboggans.
Glide wax describes a range of waxes which can be applied to Nordic
skis, alpine
skis, and snowboard
s. The gliding property of a ski is an attempt to optimize the thickness of the thin film of water between the ski and the snow. Skiing over snow is a combination of both wet friction and dry friction: too much water will create "wet drag
" (suction
), while too little water will result in "dry drag
" (friction
). A properly selected glide wax will aid in this delicate balance.
Available glide waxes contain a number of different components to match to prevailing conditions to obtain an ideal water film thickness. Obtaining an ideal water film thickness involves the glide wax contributing to the production of the water film and the removal of excess water; glide waxes contain components for both of these contributions. In conditions where creating sufficient water film are difficult (dry or very cold conditions) glide waxes will have dry friction components added. Adjusting the hardness of the glide wax is the principal method for controlling the contribution to the water film. Harder glide wax will generate more film while softer glide wax will generate less film. When excess water is present then more hydrophobic components are used for film thickness reduction.
There are a number of different components used to reduce wet friction. Paraffin wax, both natural and synthetic, has been a widely used material. Some older materials used have included pine tar and food grade oils. Other materials currently used to control wet friction include but are not limited to silicon, PTFE, flurocarbons, graphite, molybdenum and gallium though all have an effect on the glide wax hardness once added. There are numerous materials that have been used or tried but have been abandoned due to regulation or competition rules.
For controlling the hardness of glide wax the length of the carbon chains in the wax are adjusted. Longer carbon chains create a harder wax while short carbon chains create softer waxes. Microcrystalline waxes are very small allowing for very soft waxes. Other additives that affect hardness include materials also mentioned for wet friction reduction. Various mixtures of these materials will change the overall hardness.
A glide wax is selected based primarily on snow temperature, as well as the crystal structure and relative humidity of the snow. Manufacturers' packages generally provide guidelines for matching a glide wax to the snow conditions. It is applied to the "glide zone" of a ski. For alpine skis, snowboards, Nordic jumping skis, and Telemark skis, the glide zone consists of the entire base, except for the raised tip. For cross-country skis, the glide zone depends on the style of skiing being done. For the skating technique, the entire base is a glide zone, but for the classical technique, the glide zone will be the tips and tails of the ski, but not the kick zone (see below).
with a classical technique. This wax comes in two forms, "Hard Kick Wax" and "klister". Kick wax is a firm substance which comes in a small tin. It is used for new snow with a clearly defined crystal structure, and sometimes for older, cold snow (found when the air temperature is below freezing). In general, it is best used in conditions below freezing. If no kick waxes work, you may have to resort to Klister, an amorphous solid which comes in containers similar to toothpaste tubes. Klister is notoriously sticky and deserves its reputation as a difficult wax to use, but is excellent when used in icy conditions (below freezing, when the snow has lost good crystal structure) or with snow that is relatively warm and wet (above freezing). In times when Kick wax and Klister don't produce enough grip, skiers will sometimes make Hairies: a process of turning the skis into waxless cross country skis by roughing up the base significantly. If a skier owns waxless skis, or a pair of Fischer Zeros, these can be used as well.
Although the nuances of grip waxing are incredibly complex, all grip waxes serve the same purpose. The wax is applied to the central portion of the ski called the "kick zone". The kick zone extends from skier's heel to about 15 cm ahead of the binding. When enough pressure is applied downward, the camber in the ski is flattened, allowing the kick zone to make contact with the snow. When properly selected and applied, the wax in the kick zone grips the snow and allows the skier to propel him or herself forward. A well selected grip wax will release its hold on the snow as the pressure on the kick zone is released.
There are a wide variety of materials used for grip wax. Both natural and synthetic materials are used.
and Toko
.
The potential list of tools is very long and can include: waxing irons, scrapers, profiles/vises, brushes, files, screwdrivers, drills, thermometers, hot boxes, planers, clamps, rillers, special pads, cleaners and respirators. These tools are used not only in the direct application of the wax to the ski, but for the preparation of the ski base before applying the ski wax.
Clothes irons
are an inexpensive alternative to a special purpose waxing iron but are not recommended. These irons can easily heat to temperatures hot enough to melt the wax, but may not be accurate. Clothes irons suffer from relatively thin bases that tend to poorly distribute heat and low quality temperature control which can result in wide temperature variations during application. Clothes irons can often overshoot the desired temperature and scorch the wax, which decreases the performance of the wax and may be harmful to one's health, especially with fluorinated waxes.
Beginning around 1854, California gold rush miners held organized downhill ski races (see History of ski racing). They also discovered that bases smeared with dopes brewed from vegetable and/or animal compound helped increase skiing speeds. This led to some of the first commercial ski wax (even though they contained no wax at all), such as Black Dope and Sierra Lighting; both are mainly composed of sperm oil
, vegetable oil and pine pitch. However, some instead used paraffin candle wax that melted onto ski bases, and these worked better under colder conditions.
A significant advance for cross country racing was the introduction of klister, for good kick in warm snow; klister was invented and patented in 1913 by Peter Østbye.
Ski waxing has developed into a very complex science, its advancement motivated by ski racing. Many companies are dedicated to ski wax production and have developed full lines of wax to cover every condition for the maximum performance. The most recent great advancement in ski wax has been the use of surfactants and fluorocarbons to increase water and dirt repellency and therefore increase glide.
Surfactants were introduced in 1974 by Hertel Wax. Fluorocarbons were introduced beginning in 1986, as the result of parallel research conducted in California and Norway.
Terry Hertel is a recreational skier from the San Francisco area. He had made money during the Silicon Valley computer boom and in 1972 introduced the original ski Hot Wax applicator drum for home use. To go with it he invented a line of high-melting-point paraffin waxes branded as Hot Sauce. As a Lake Tahoe skier, Hertel was fascinated with the problem of glide at all temperatures of snow. In 1974 he formulated a surfactant to his paraffin wax to produce an all temperature wax he trademarked HotSauce. A surfactant is a wetting agent, the exact opposite of a hydrophobic agent. Surfactants are closely related to detergents: they shouldn’t normally work as hydrophobes. But the stuff Hertel used, sodium dodecyl sulfate
(SDS), is an odd columnar molecule with a hydrophobic end. Suspended in wax, the molecules clump into spheres with their hydrophobic ends out, making a kind of water-repellent ball bearing. Hertel said his surfactant ingredient was "microencapsulated", referring to a common technique using SDS and related surfactants in pharmaceutical preparation. Super HotSauce earned an insiders’ reputation for great glide in heavy snow. Town racers liked it. HotSauce gives the skier and snowboarder additional control.
A couple of years later, Hertel started research for a "Spring Solution", something that would work in very wet snow but repel the pine pollen, diesel exhaust particles and other dirt that darkened the ski slope snow in April and May. He tried polypropylene glycol, a food-grade antifreeze used to keep ice cream from melting, and it worked. But he also talked to Rob Hunter, a chemist at 3M, who mentioned that the company sold a liquid fluorocarbon to the cosmetics and paint industries: it dried to a smooth, glossy surface. Hunter thought the liquid fluorocarbon would work well in a ski wax at colder temperatures, but warned that at $1000 per pound, it was far too expensive.
Hertel wound up buying the 3M perfluorocarbon liquid in five-gallon drums, formulated it into a high-strength candle wax called Paraflint, and in 1986 introduced a hard block wax he called Racing Fluorocarbon 739. It was very hydrophobic, and very fast. (Perfluoro means that all the lateral links in the polymer chain, not just some of them, are capped with fluorine atoms.)
Hertel invented White Gold a high performance racing wax by formulating perfluoropolyether diol with the SDS formula.
Meanwhile, at Swix, chief chemist Leif Torgersen was also looking for something to repel dirt. A hard glide wax was essential to last throughout a 50 km race or a ski marathon, but the softer kick wax picked up pine pollen and other dirt, slowing the ski progressively through the course of the race. So he sought a form of fluorocarbon that could be ironed into the base. In Italy, he found it: Enrico Traverso at Enichem SpA, a state-owned industrial giant, had a fluorcarbon powder with a melting temperature just a few degrees below that that of sintered polyethylene. That meant that if you were careful, you could iron it without destroying the ski base. Enichem had no other commercial customers for the material, but were willing to produce small, expensive lots for use in ski waxes.
Swix began experimenting with the stuff on race courses and found that it improved glide by about 2 percent over the best non-fluorocarbon waxes. In 1990 the company introduced a commercial version called Cera F (cera is Italian for wax). The price: $100 for 30 grams. The parents of young racers screamed in agony: apparently you couldn’t win without it. Fortunately, a little went a long way. Speed skier C.J. Mueller remembers waxing his skis with the scrapings from another competitor’s skis.
Belatedly, it occurred to the various parties in this technology race to patent their products. On March 2, 1990, Enichem applied for an Italian patent on a "ski lubricant comprising paraffinic wax and hydrocarbon compounds containing a perfluorocarbon segment". The same day, Hertel filed for a U.S. patent on a "ski wax for use with sintered-base snow skis", containing paraffin, a hardener wax, roughly 1% per-fluoroether diol, and 2% SDS surfactant". Enichem received a U.S. patent a year later.
These are the two earliest patents for fluorocarbon ski waxes. Later patents have been granted to Dupont and to Athanasios Karydas, Technical Director (and owner) of DOMINATOR Race Wax, a U.S. company (dominatorwax.com).
Hertel claims his Racing Fluorocarbon 739 product quickly found its way into the waxing kits of World Cup technicians and has been used in a number of medal-winning performances. However, he’s never been a member of any alpine supplier pool (minimum annual buy-in costs $50,000). Hertel has provided specialized waxes for freestyle aerials, because in corn-snow conditions are rough at the entry to a kicker and can hold a large volume of water. European companies Swix, Toko, Holmenkol, Briko, and Maplus, who comprise the supplier pools for ski wax, don’t talk about the advanced technology they may be using on World Cup skis.
Dragonski one of the most advance ski wax brand for cross country and alpin in world cup is now using tungsten and molybden for preserving base from friction. And now dragonski is stetting a Portable Race on site Research and Development Lab
Has enable are team of CHEMISTS to test the data generated from the racers feedback by working directly with World Cup Ski Teams. This wealth of Data and Testing has helped with the Development of are First Generation of Hybrid waxes. The PFX molecule features higher and longer thermal and chemical capabilities that meet the top level requirements in colder temperatures of Lillehammer as well as in warmer conditions of Nagano..
, benzene
(carcinogenic) or mineral spirits. However commercial wax solvents are made from citrus oil, which is less toxic, harder to ignite, and least damaging (if at all) to the ski base.
, are known to increase dramatically in ski wax technicians during the ski season. PFOA, in particular, is known to be stable in the environment and to cause cancer, birth defects, thyroid dysfunction, increased cardiovascular risk, hormone and immune system disruption, birth and developmental defects and liver toxicity
Ski
A ski is a long, flat device worn on the foot, usually attached through a boot, designed to help the wearer slide smoothly over snow. Originally intended as an aid to travel in snowy regions, they are now mainly used for recreational and sporting purposes...
s or snowboard
Snowboard
Snowboards are boards, usually with a width the length of one's foot, with the ability to glide on snow. Snowboards are differentiated from monoskis by the stance of the user...
s to improve the ski's performance on snow. It can also be applied to other devices that slide over snow and ice such as toboggans.
Types of ski wax
In general, ski wax can be divided into two major categories: "glide" and "grip".Glide wax
Glide wax is used by all skiing disciplines. It can offer improved glide speed versus an unwaxed ski.Glide wax describes a range of waxes which can be applied to Nordic
Nordic skiing
Nordic skiing is a winter sport that encompasses all types of skiing where the heel of the boot cannot be fixed to the ski, as opposed to Alpine skiing....
skis, alpine
Alpine skiing
Alpine skiing is the sport of sliding down snow-covered hills on skis with fixed-heel bindings. Alpine skiing can be contrasted with skiing using free-heel bindings: Ski mountaineering and nordic skiing – such as cross-country; ski jumping; and Telemark. In competitive alpine skiing races four...
skis, and snowboard
Snowboard
Snowboards are boards, usually with a width the length of one's foot, with the ability to glide on snow. Snowboards are differentiated from monoskis by the stance of the user...
s. The gliding property of a ski is an attempt to optimize the thickness of the thin film of water between the ski and the snow. Skiing over snow is a combination of both wet friction and dry friction: too much water will create "wet drag
Drag (physics)
In fluid dynamics, drag refers to forces which act on a solid object in the direction of the relative fluid flow velocity...
" (suction
Suction
Suction is the flow of a fluid into a partial vacuum, or region of low pressure. The pressure gradient between this region and the ambient pressure will propel matter toward the low pressure area. Suction is popularly thought of as an attractive effect, which is incorrect since vacuums do not...
), while too little water will result in "dry drag
Drag (physics)
In fluid dynamics, drag refers to forces which act on a solid object in the direction of the relative fluid flow velocity...
" (friction
Friction
Friction is the force resisting the relative motion of solid surfaces, fluid layers, and/or material elements sliding against each other. There are several types of friction:...
). A properly selected glide wax will aid in this delicate balance.
Available glide waxes contain a number of different components to match to prevailing conditions to obtain an ideal water film thickness. Obtaining an ideal water film thickness involves the glide wax contributing to the production of the water film and the removal of excess water; glide waxes contain components for both of these contributions. In conditions where creating sufficient water film are difficult (dry or very cold conditions) glide waxes will have dry friction components added. Adjusting the hardness of the glide wax is the principal method for controlling the contribution to the water film. Harder glide wax will generate more film while softer glide wax will generate less film. When excess water is present then more hydrophobic components are used for film thickness reduction.
There are a number of different components used to reduce wet friction. Paraffin wax, both natural and synthetic, has been a widely used material. Some older materials used have included pine tar and food grade oils. Other materials currently used to control wet friction include but are not limited to silicon, PTFE, flurocarbons, graphite, molybdenum and gallium though all have an effect on the glide wax hardness once added. There are numerous materials that have been used or tried but have been abandoned due to regulation or competition rules.
For controlling the hardness of glide wax the length of the carbon chains in the wax are adjusted. Longer carbon chains create a harder wax while short carbon chains create softer waxes. Microcrystalline waxes are very small allowing for very soft waxes. Other additives that affect hardness include materials also mentioned for wet friction reduction. Various mixtures of these materials will change the overall hardness.
A glide wax is selected based primarily on snow temperature, as well as the crystal structure and relative humidity of the snow. Manufacturers' packages generally provide guidelines for matching a glide wax to the snow conditions. It is applied to the "glide zone" of a ski. For alpine skis, snowboards, Nordic jumping skis, and Telemark skis, the glide zone consists of the entire base, except for the raised tip. For cross-country skis, the glide zone depends on the style of skiing being done. For the skating technique, the entire base is a glide zone, but for the classical technique, the glide zone will be the tips and tails of the ski, but not the kick zone (see below).
Grip wax
Grip wax describes a variety of waxes specific to cross-country skiingCross-country skiing
Cross-country skiing is a winter sport in which participants propel themselves across snow-covered terrain using skis and poles...
with a classical technique. This wax comes in two forms, "Hard Kick Wax" and "klister". Kick wax is a firm substance which comes in a small tin. It is used for new snow with a clearly defined crystal structure, and sometimes for older, cold snow (found when the air temperature is below freezing). In general, it is best used in conditions below freezing. If no kick waxes work, you may have to resort to Klister, an amorphous solid which comes in containers similar to toothpaste tubes. Klister is notoriously sticky and deserves its reputation as a difficult wax to use, but is excellent when used in icy conditions (below freezing, when the snow has lost good crystal structure) or with snow that is relatively warm and wet (above freezing). In times when Kick wax and Klister don't produce enough grip, skiers will sometimes make Hairies: a process of turning the skis into waxless cross country skis by roughing up the base significantly. If a skier owns waxless skis, or a pair of Fischer Zeros, these can be used as well.
Although the nuances of grip waxing are incredibly complex, all grip waxes serve the same purpose. The wax is applied to the central portion of the ski called the "kick zone". The kick zone extends from skier's heel to about 15 cm ahead of the binding. When enough pressure is applied downward, the camber in the ski is flattened, allowing the kick zone to make contact with the snow. When properly selected and applied, the wax in the kick zone grips the snow and allows the skier to propel him or herself forward. A well selected grip wax will release its hold on the snow as the pressure on the kick zone is released.
There are a wide variety of materials used for grip wax. Both natural and synthetic materials are used.
Glide waxing process
Glide waxing is more common than grip waxing, simply because alpine skis, snowboards, waxless cross-country skis, and skate skis can all be treated with glide wax, but only plain cross-country skis need grip wax. Waxless cross-country skis usually have etched gripping surfaces that eliminate the need to apply grip wax. Usually, the process begins with a cleaning of the board by using specifically formulated wax remover (see below), which removes both the old wax and any other dirt that may interfere with the adhesion of the wax. After the bare ski base is exposed, there are typically three methods of waxing:Hot waxing
Wax appropriate for the anticipated temperature range is heated up against the iron, melted, and dripped or 'crayoned' onto the base of a ski or snowboard. The wax is then ironed into the base using a heated iron. Softer waxes, better for warmer conditions, require lower iron temperatures than do harder waxes, which are meant for colder conditions and require higher iron temperatures; the appropriate ironing temperature for a given wax is often listed on its packaging. After allowing the base to cool, the excess wax is scraped off. Then the ski is brushed with coarse metal brushes, then softer nylon and horse hair brushes to create a smooth, fast, base, often highly fluorinated wax (wax in which many of the bonded hydrogens have been replaced with fluorine) is used to reduce the friction between ski and snow even more.Paste, liquid, spray-on, and rub-on waxing
These are the simplest waxing methods. Generally all that is required is to smear, rub, spray or apply a thin layer liquid wax onto the ski's base using a paint brush, then let dry before buffing it into the ski base with a waxing cork. A common misconception is that waxes applied with this method offer the least performance and require frequent re-application. Liquid and spray waxes in particular provide better coverage than solid wax applied with an iron, however to achieve the same durability as hot waxing an iron is used after liquid or spray wax application to maximize penetration of the wax into the base.Hotboxing
Another method, hotboxing, consists of applying a wax with an iron, then warming skis in a device called a hotbox. Hotboxes open up the pores in the ski, this allows the recently applied wax to penetrate the base of the ski deeper and more effectively, creating an even faster gliding surface. Hotboxes can be home made—an insulated box with a heater is the basic setup—although commercial made hotboxes are available from manufacturers such as SwixSwix
Swix is a Norwegian company producing ski wax, ski poles and sportswear. The company is owned by the investment company Ferd AS, and has the head office in Lillehammer....
and Toko
Toko
Toko is a small rural settlement 10 kilometres east of Stratford, New Zealand, at the intersection of East Road and Toko Road. It is located on a railway, the Stratford - Okahukura Line, the western portion of which was operated as a branch line known as the Toko Branch prior to the line's...
.
Kick Wax
This comes in three forms: the traditional hard wax in an aluminum tin, as a liquid paste and as a tape. The three forms can be used by recreational, fitness and racing skiers.Klister wax
Klister wax comes in a squeeze tube or a spray-on can and is best applied in a warm location. It is squeezed out of its tube onto the kick zone of the ski, and then spread using a paddle or with a thumb.Hairies
There are times when neither kick wax nor klister can create effective grip; a technique that is not technically waxing is used to create grip in a particularly specific snow/air temperature (around 0°C) and snow grain (new, abrasive snow). This technique is called "making hairies". The kick zone of the ski is cleaned, then roughened by using fairly coarse sandpaper (usually at least 80 grit). Lastly, a layer of silicone is sprayed over the textured base to discourage ice from sticking to the "hairs" of ptex.Application tools
There are a wide variety of tools that can be used to aid in the application of ski wax. For glide waxing the basic tools are typically a waxing iron, a plastic scraper and a nylon brush. For grip waxing a cork (natural or synthetic) for application and a plastic scraper for removal (though not the one used for glide wax).The potential list of tools is very long and can include: waxing irons, scrapers, profiles/vises, brushes, files, screwdrivers, drills, thermometers, hot boxes, planers, clamps, rillers, special pads, cleaners and respirators. These tools are used not only in the direct application of the wax to the ski, but for the preparation of the ski base before applying the ski wax.
Waxing irons
Special-purpose ski waxing irons have more accurate temperature controls, and thicker and smoother bases. Thick bases help keep the heat evenly distributed over the iron's surface. The more accurate temperature control means the iron maintains the selected temperature without excessive temperature spikes or drops. All together this results in better wax penetration into the ski base because each wax has an ideal application temperature. The iron's flat base also allows for easy cleaning so that waxes from previous applications do not become mixed with the current application resulting in a contaminated wax mixture.Clothes irons
Iron (appliance)
A clothes iron, also referred to as simply an iron, is a small appliance used in ironing to remove wrinkles from fabric.Ironing works by loosening the ties between the long chains of molecules that exist in polymer fiber materials. With the heat and the weight of the ironing plate, the fibers are...
are an inexpensive alternative to a special purpose waxing iron but are not recommended. These irons can easily heat to temperatures hot enough to melt the wax, but may not be accurate. Clothes irons suffer from relatively thin bases that tend to poorly distribute heat and low quality temperature control which can result in wide temperature variations during application. Clothes irons can often overshoot the desired temperature and scorch the wax, which decreases the performance of the wax and may be harmful to one's health, especially with fluorinated waxes.
Corks
Corks come in two materials: natural and synthetic. They come in small and large blocks. The corks are used primarily for the spreading of Nordic grip waxes. But they are also used extensively by Nordic and Alpine skiers for applying the high-end fluorocarbon powders. A special cork on a roller called roto-cork is used for pure fluorocarbon wax applications.Profiles/Vises
These help hold the ski or snowboard in place while waxing and/or tuning is performed. There are different profiles and vises for Nordic skis, Alpine skis and snowboards. Some are large and meant to be left fixed on a workbench while others are portable.Brushes
Generally the purpose of brushing is to remove the final thin excess layer of wax from the ski without damaging the bases or changing the structure of the ski base. The specialty brushes are used to prepare the ski base and/or deal with very hard waxes. The wide variety of conditions and waxes require a large array of brushes which vary depending on material, bristle stiffness, bristle diameter and size. While it is unnecessary for recreational skiers to have every kind of brush, more serious skiers and wax technicians will have them all. The brush types include stiff nylon (general purpose), soft nylon (finishing/polishing), horsehair (soft and hard), brass (fine and extra fine), copper, fine steel, coarse steel and combination brushes.History
Johannes Scheffer in Argentoratensis Lapponiæ (History of Lapland) in 1673 probably gave the first recorded instruction for ski wax application He advised skiers to use pine tar pitch and rosin.Beginning around 1854, California gold rush miners held organized downhill ski races (see History of ski racing). They also discovered that bases smeared with dopes brewed from vegetable and/or animal compound helped increase skiing speeds. This led to some of the first commercial ski wax (even though they contained no wax at all), such as Black Dope and Sierra Lighting; both are mainly composed of sperm oil
Whale oil
Whale oil is the oil obtained from the blubber of various species of whales, particularly the three species of right whale and the bowhead whale prior to the modern era, as well as several other species of baleen whale...
, vegetable oil and pine pitch. However, some instead used paraffin candle wax that melted onto ski bases, and these worked better under colder conditions.
A significant advance for cross country racing was the introduction of klister, for good kick in warm snow; klister was invented and patented in 1913 by Peter Østbye.
Ski waxing has developed into a very complex science, its advancement motivated by ski racing. Many companies are dedicated to ski wax production and have developed full lines of wax to cover every condition for the maximum performance. The most recent great advancement in ski wax has been the use of surfactants and fluorocarbons to increase water and dirt repellency and therefore increase glide.
Surfactants were introduced in 1974 by Hertel Wax. Fluorocarbons were introduced beginning in 1986, as the result of parallel research conducted in California and Norway.
Terry Hertel is a recreational skier from the San Francisco area. He had made money during the Silicon Valley computer boom and in 1972 introduced the original ski Hot Wax applicator drum for home use. To go with it he invented a line of high-melting-point paraffin waxes branded as Hot Sauce. As a Lake Tahoe skier, Hertel was fascinated with the problem of glide at all temperatures of snow. In 1974 he formulated a surfactant to his paraffin wax to produce an all temperature wax he trademarked HotSauce. A surfactant is a wetting agent, the exact opposite of a hydrophobic agent. Surfactants are closely related to detergents: they shouldn’t normally work as hydrophobes. But the stuff Hertel used, sodium dodecyl sulfate
Sodium dodecyl sulfate
Sodium dodecyl sulfate , sodium laurilsulfate or sodium lauryl sulfate is an organic compound with the formula CH311OSO3Na). It is an anionic surfactant used in many cleaning and hygiene products...
(SDS), is an odd columnar molecule with a hydrophobic end. Suspended in wax, the molecules clump into spheres with their hydrophobic ends out, making a kind of water-repellent ball bearing. Hertel said his surfactant ingredient was "microencapsulated", referring to a common technique using SDS and related surfactants in pharmaceutical preparation. Super HotSauce earned an insiders’ reputation for great glide in heavy snow. Town racers liked it. HotSauce gives the skier and snowboarder additional control.
A couple of years later, Hertel started research for a "Spring Solution", something that would work in very wet snow but repel the pine pollen, diesel exhaust particles and other dirt that darkened the ski slope snow in April and May. He tried polypropylene glycol, a food-grade antifreeze used to keep ice cream from melting, and it worked. But he also talked to Rob Hunter, a chemist at 3M, who mentioned that the company sold a liquid fluorocarbon to the cosmetics and paint industries: it dried to a smooth, glossy surface. Hunter thought the liquid fluorocarbon would work well in a ski wax at colder temperatures, but warned that at $1000 per pound, it was far too expensive.
Hertel wound up buying the 3M perfluorocarbon liquid in five-gallon drums, formulated it into a high-strength candle wax called Paraflint, and in 1986 introduced a hard block wax he called Racing Fluorocarbon 739. It was very hydrophobic, and very fast. (Perfluoro means that all the lateral links in the polymer chain, not just some of them, are capped with fluorine atoms.)
Hertel invented White Gold a high performance racing wax by formulating perfluoropolyether diol with the SDS formula.
Meanwhile, at Swix, chief chemist Leif Torgersen was also looking for something to repel dirt. A hard glide wax was essential to last throughout a 50 km race or a ski marathon, but the softer kick wax picked up pine pollen and other dirt, slowing the ski progressively through the course of the race. So he sought a form of fluorocarbon that could be ironed into the base. In Italy, he found it: Enrico Traverso at Enichem SpA, a state-owned industrial giant, had a fluorcarbon powder with a melting temperature just a few degrees below that that of sintered polyethylene. That meant that if you were careful, you could iron it without destroying the ski base. Enichem had no other commercial customers for the material, but were willing to produce small, expensive lots for use in ski waxes.
Swix began experimenting with the stuff on race courses and found that it improved glide by about 2 percent over the best non-fluorocarbon waxes. In 1990 the company introduced a commercial version called Cera F (cera is Italian for wax). The price: $100 for 30 grams. The parents of young racers screamed in agony: apparently you couldn’t win without it. Fortunately, a little went a long way. Speed skier C.J. Mueller remembers waxing his skis with the scrapings from another competitor’s skis.
Belatedly, it occurred to the various parties in this technology race to patent their products. On March 2, 1990, Enichem applied for an Italian patent on a "ski lubricant comprising paraffinic wax and hydrocarbon compounds containing a perfluorocarbon segment". The same day, Hertel filed for a U.S. patent on a "ski wax for use with sintered-base snow skis", containing paraffin, a hardener wax, roughly 1% per-fluoroether diol, and 2% SDS surfactant". Enichem received a U.S. patent a year later.
These are the two earliest patents for fluorocarbon ski waxes. Later patents have been granted to Dupont and to Athanasios Karydas, Technical Director (and owner) of DOMINATOR Race Wax, a U.S. company (dominatorwax.com).
Hertel claims his Racing Fluorocarbon 739 product quickly found its way into the waxing kits of World Cup technicians and has been used in a number of medal-winning performances. However, he’s never been a member of any alpine supplier pool (minimum annual buy-in costs $50,000). Hertel has provided specialized waxes for freestyle aerials, because in corn-snow conditions are rough at the entry to a kicker and can hold a large volume of water. European companies Swix, Toko, Holmenkol, Briko, and Maplus, who comprise the supplier pools for ski wax, don’t talk about the advanced technology they may be using on World Cup skis.
Dragonski one of the most advance ski wax brand for cross country and alpin in world cup is now using tungsten and molybden for preserving base from friction. And now dragonski is stetting a Portable Race on site Research and Development Lab
Has enable are team of CHEMISTS to test the data generated from the racers feedback by working directly with World Cup Ski Teams. This wealth of Data and Testing has helped with the Development of are First Generation of Hybrid waxes. The PFX molecule features higher and longer thermal and chemical capabilities that meet the top level requirements in colder temperatures of Lillehammer as well as in warmer conditions of Nagano..
Wax solvents
Wax can be dissolved by nonpolar solvents like gasolineGasoline
Gasoline , or petrol , is a toxic, translucent, petroleum-derived liquid that is primarily used as a fuel in internal combustion engines. It consists mostly of organic compounds obtained by the fractional distillation of petroleum, enhanced with a variety of additives. Some gasolines also contain...
, benzene
Benzene
Benzene is an organic chemical compound. It is composed of 6 carbon atoms in a ring, with 1 hydrogen atom attached to each carbon atom, with the molecular formula C6H6....
(carcinogenic) or mineral spirits. However commercial wax solvents are made from citrus oil, which is less toxic, harder to ignite, and least damaging (if at all) to the ski base.
Health and Environmental Impacts
Ski wax can contain toxic chemicals including perfluorinated chemicals. Levels of perfluorinated carbolylates, especially perfluorooctanoic acidPerfluorooctanoic acid
Perfluorooctanoic acid , also known as C8 and perfluorooctanoate, is a synthetic, stable perfluorinated carboxylic acid and fluorosurfactant. One industrial application is as a surfactant in the emulsion polymerization of fluoropolymers. It has been used in the manufacture of such prominent...
, are known to increase dramatically in ski wax technicians during the ski season. PFOA, in particular, is known to be stable in the environment and to cause cancer, birth defects, thyroid dysfunction, increased cardiovascular risk, hormone and immune system disruption, birth and developmental defects and liver toxicity
Brands
- Purl Wax: faster than you. Environmentally friendly organic ski wax and snowboard wax
- Crack Grease: Sustainable and locally-sourced snowboard wax
- BeaverWax: environmentally friendly additives
- Glide-on Wax
- SwixSwixSwix is a Norwegian company producing ski wax, ski poles and sportswear. The company is owned by the investment company Ferd AS, and has the head office in Lillehammer....
- TokoMammut sports groupMammut Sports Group AG is a Swiss producer of mountaineering and trekking equipment with headquarters in Seon, Switzerland. The company was founded in 1862 by Kaspar Tanner in Dintikon. Today, Mammut belongs to Conzzeta AG...
- KuuKuusportKUUsport Manufacturing is a Toronto based Canadian company producing ski wax and related ski tuning equipment. The name is derived from Ron Kuus, the founder. The company was incorporated in 1986.KUU is an official supplier to Canadian and Austrian ski teams....
- Solda
- Hertelskiwax
- Whacks Wax
- Bluebird
- FastWax
- Dragonski