Microtunneling
Encyclopedia
As the name implies, microtunneling is a digging technique used to construct small tunnel
s. These small diameter tunnels make it impossible to have an operator in the machine itself. Instead, the microtunnel boring machine (MTBM) must be operated remotely.
Microtunnel boring machines are very similar to tunnel boring machine
s (TBM) but on a smaller scale. These machines generally vary from 0.61 metre but smaller and larger machines have existed. Usually the operator controls the machine from a control room on the surface of the ground. The operator is given constant feedback about the machine’s location, orientation and hydraulic devices via a computer console. Most machines also have video cameras set up to give the operator more information. The operator can then control the MTBM and the jacking frame from the safety of the control room.
In most microtunneling operations the pipe is inserted from the entry and pushed behind the machine. This is a process often called Pipe Jacking. As the machine advances, more tunnel liner is pushed from the entrance. Thus, the speed of the advancing machine is controlled by the speed at which the pipe is inserted into the entrance.
As the length of tunnel increases, the friction of the ground around the pipe increases as well. Usually, two practices are used to minimize this friction. First, over-cutting is used to give a slight gap between the inner edge of the tunnel and the outer edge of the liner. Usually this is achieved by using a cutter wheel with a diameter ½ inch (12mm) to 4 inches (100mm) larger than the outside diameter of the liner. Secondly, an economical and ecologically friendly lubricant
, often bentonite
slurry
, is injected into this gap. In addition to lubrication, the pressure of the lubricant prevents the gap from collapsing.
While friction can be reduced, it can never be eliminated, and so hundreds of tons of force are required to push the machine and liner into the ground. A large “jacking frame” is required to produce these forces. In most cases the entrance must be modified to support this frame and the forces it generates.
In addition to the jacking frame, smaller jacks, called “interjacks”, may be inserted between sections of tunnel liner. These push the two sections of liner apart. Friction on the liner sections between the interjack and the tunnel entrance helps to prevent the liner from sliding out backwards. So while the liner behind the interjack does not move, those sections in front of it receive additional pushing force.
Tunnel
A tunnel is an underground passageway, completely enclosed except for openings for egress, commonly at each end.A tunnel may be for foot or vehicular road traffic, for rail traffic, or for a canal. Some tunnels are aqueducts to supply water for consumption or for hydroelectric stations or are sewers...
s. These small diameter tunnels make it impossible to have an operator in the machine itself. Instead, the microtunnel boring machine (MTBM) must be operated remotely.
Microtunnel boring machines are very similar to tunnel boring machine
Tunnel boring machine
A tunnel boring machine also known as a "mole", is a machine used to excavate tunnels with a circular cross section through a variety of soil and rock strata. They can bore through anything from hard rock to sand. Tunnel diameters can range from a metre to almost 16 metres to date...
s (TBM) but on a smaller scale. These machines generally vary from 0.61 metre but smaller and larger machines have existed. Usually the operator controls the machine from a control room on the surface of the ground. The operator is given constant feedback about the machine’s location, orientation and hydraulic devices via a computer console. Most machines also have video cameras set up to give the operator more information. The operator can then control the MTBM and the jacking frame from the safety of the control room.
In most microtunneling operations the pipe is inserted from the entry and pushed behind the machine. This is a process often called Pipe Jacking. As the machine advances, more tunnel liner is pushed from the entrance. Thus, the speed of the advancing machine is controlled by the speed at which the pipe is inserted into the entrance.
As the length of tunnel increases, the friction of the ground around the pipe increases as well. Usually, two practices are used to minimize this friction. First, over-cutting is used to give a slight gap between the inner edge of the tunnel and the outer edge of the liner. Usually this is achieved by using a cutter wheel with a diameter ½ inch (12mm) to 4 inches (100mm) larger than the outside diameter of the liner. Secondly, an economical and ecologically friendly lubricant
Lubricant
A lubricant is a substance introduced to reduce friction between moving surfaces. It may also have the function of transporting foreign particles and of distributing heat...
, often bentonite
Bentonite
Bentonite is an absorbent aluminium phyllosilicate, essentially impure clay consisting mostly of montmorillonite. There are different types of bentonite, each named after the respective dominant element, such as potassium , sodium , calcium , and aluminum . Experts debate a number of nomenclatorial...
slurry
Slurry
A slurry is, in general, a thick suspension of solids in a liquid.-Examples of slurries:Examples of slurries include:* Lahars* A mixture of water and cement to form concrete* A mixture of water, gelling agent, and oxidizers used as an explosive...
, is injected into this gap. In addition to lubrication, the pressure of the lubricant prevents the gap from collapsing.
While friction can be reduced, it can never be eliminated, and so hundreds of tons of force are required to push the machine and liner into the ground. A large “jacking frame” is required to produce these forces. In most cases the entrance must be modified to support this frame and the forces it generates.
In addition to the jacking frame, smaller jacks, called “interjacks”, may be inserted between sections of tunnel liner. These push the two sections of liner apart. Friction on the liner sections between the interjack and the tunnel entrance helps to prevent the liner from sliding out backwards. So while the liner behind the interjack does not move, those sections in front of it receive additional pushing force.