Coulter principle
Encyclopedia
The term “Coulter Principle” refers to the use of an electric field for counting and sizing dilute suspensions of particles in conducting liquids. The phrase was coined when Wallace H. Coulter was awarded US Patent #2,656,508, Means for Counting Particles Suspended in a Fluid. The Coulter Principle is most commonly employed in a COULTER COUNTER®, which is an analytical instrument designed for a specific task such as counting cells. However, there are numerous other ways to implement the Coulter Principle. Several of these have been attempted, some with commercial success, and some purely for academic research. To date, the most commercially successful application of the Coulter Principle is in hematology, where it is used to obtain information about patients’ blood cells. While the Coulter Principle and Coulter Counters have appeared in many thousands of peer-reviewed research papers over the past 5 decades, most people remain unfamiliar with it unless they have personally encountered it in a laboratory environment. This Wikipedia page provides a primer on the Coulter Principle.

The Coulter Principle General Description

The Coulter Principle relies on the fact that particles moving in an electric field cause measurable disturbances in that field. The magnitudes of these disturbances are proportional to the size of the particles in the field. Coulter identified several requirements necessary for practical application of this phenomenon. First, the particles should be suspended in a conducting liquid. Second, the electrical field should be physically constricted so that the movement of particles in the field causes detectable changes in the current. Finally, the particles should be dilute enough so that only one at a time passes through the physical constriction, preventing an artifact known as coincidence.

Typical Implementations

While the Coulter Principle can be implemented in a variety of designs, there are two that have become the most commercially relevant. These include an aperture format and a flow cell format. The Figure above shows several other geometries that Coulter patented.

Aperture Format

The aperture format is used in most commercial Coulter counters. In this set up, an orifice of defined size is created in a jewel disk using special manufacturing processes. The resulting aperture is then embedded in the wall of a glass tube. The product of this process is commonly referred to as an aperture tube. While in use, the aperture tube is placed in a liquid so that the jewel disk is completely submerged and the tube can fill with liquid. Electrodes are positioned both inside and outside the aperture tube, which allows current to flow through the aperture. A pump is used to create a vacuum at the top of the tube, which draws the liquid through the aperture. Samples to be analyzed are then slowly added to the conducting liquid surrounding the aperture tube. At the start of the experiment, the electric field is turned on and the pump begins to draw the dilute suspension through the aperture. The resulting data are collected by recording the electrical pulses generated as the particles traverse the aperture.
While the basic physical set-up of the aperture format is consistent in every COULTER COUNTER®, the amount and quality of data varies greatly as a function of the signal processing circuitry implemented. For example, amplifiers with lower noise thresholds and greater dynamic range can increase the sensitivity of the system. Similarly, digital pulse height analyzers with variable bin widths provide much higher resolution data as opposed to analog analyzers with fixed bins. Further, combining a COULTER COUNTER® with a digital computer allows capture of many electrical pulse characteristics, while analog counters typically store a much more limited amount of information about each pulse.

Flow Cell Format

The flow cell format is most commonly implemented in hematology instruments, and sometimes flow cytometers. In this format, electrodes are embedded at either end of a flow channel and the electric field is applied through the channel. This format has several advantages as opposed to the aperture format. This arrangement allows for continuous sample analysis whereas the aperture format is single-batch format. Further, the use of a flow cell lends itself to addition of a sheath flow, which keeps particles centered in the middle of the flow channel. This allows additional measurements to be performed simultaneously, such as probing the object with a laser. The major disadvantages of the flow cell format are that it is much more expensive to manufacture and is typically fixed to one channel width, whereas the aperture format offers a wide variety of aperture sizes.

Coincidence

Anomalous electrical pulses can be generated if the concentration of sample is so high that multiple particles enter the aperture simultaneously. This situation is known as coincidence. The problem occurs because there is no way to ensure that a single large pulse is the result of a single large particle or multiple small particles entering the aperture at once. In order to prevent this situation, samples must be fairly dilute.

Particle Path

The shape of the generated electrical pulse varies with the particle path through the aperture. Shoulders and other artifacts can occur because the electric field density varies across the diameter of the aperture. Thus, a particle’s path through the field will impact the shape of the electric pulse generated. This variance is a result of both the physical constriction of the electric field and also the fact that the liquid velocity varies as a function of radial location in the aperture. In the flow cell format, this effect is minimized since sheath flow ensures each particle travels an almost identical path through the flow cell. In the aperture format, signal processing algorithms can be used to correct for artifacts resulting from particle path.

Conductive Particles

Conductive particles are a common concern for individuals considering the Coulter Principle. While this topic raises interesting scientific questions, practically, it rarely effects the results of an experiment. This is because the conductivity difference between most conductive materials and ions in liquid (referred to as the discharge potential) is so great that most conductive materials act as insulators in a COULTER COUNTER®. The voltage necessary to breakdown this potential barrier is referred to as the breakdown voltage. For those highly conductive materials that present a problem, the voltage used during a Coulter experiment should be reduced below the breakdown potential (which can be determined empirically).

Porous particles

The Coulter Principle measures the volume of an object, since the disturbance in the electric field is proportional to the volume of electrolyte displaced from the aperture. This leads to some confusion amongst those who are used to optical measurements from microscopes or other systems that only view two dimensions and also show the boundaries of an object. The Coulter Principle, on the other hand measures three dimensions and the volume displaced by an object. It is most useful to think of sponges-even though a wet sponge may appear very large, it will displace significantly less liquid than a solid brick of the same dimensions.

Direct current vs alternating current

Direct current is used in the Coulter counters found in most research and cell laboratories. Direct current measurements are useful for an array of particles and allow for simplified data acquisition and processing. Alternating current measurements are sometime used in clinical hematology instruments, due to the special nature of cell membranes. At low frequencies (below 500 kHz), alternating and direct current measurements behave essentially the same way. At intermediate frequencies (500 kHz-6MHZ), the plasma membrane of cells can become polarized, leading to a decreased capacitance of the measurement systems. However, at high frequencies (6-20 Mhz), the cell membrane loses its polarization, and the electrical pulses provide information about the cell cytoplasm.

Hematology

The most successful and important application of the Coulter Principle is in the characterization of human blood cells. The technique has been used to diagnose a variety of diseases, and is the standard method for obtaining red blood cell counts (RBCs) and white blood cell counts (WBCs) as well as several other common parameters. When combined with other technologies such as fluorescence tagging and light scattering, the Coulter Principle can help produce a detailed profile of patients’ blood cells.

Cell count and size

In addition to clinical blood cells (~6-10 micrometres, typically), the Coulter principle has established itself as the most reliable laboratory method for counting a wide variety of cells, ranging from bacteria (< 1 micrometre in size), fat cells (~400 micrometre), plant cell aggregates (~>1200 micrometre), and stem cell embryoid bodies (~900 micrometre). The technique has become so standardized that ASTM International (formerly American Society for Testing and Materials) has published a procedure on the topic: ASTMF2149-01(2007) Standard Test Method for Automated Analyses of Cells-the Electrical Sensing Zone Method of Enumerating and Sizing Single Cell Suspensions (http://www.astm.org/Standards/F2149.htm).

Particle characterization

The Coulter Principle has proved useful to applications well beyond cellular studies. The fact that it individually measures particles, is independent of any optical properties, is extremely sensitive, and is very reproducible has appeal to a wide variety of fields. To illustrate, below are listed some of the ASTM Methods that have been written for the Coulter Principle (Sometimes referred to as “Electrical Sensing Zone”). Note the wide variety of materials that they encompass.

-Test Method C690-86 (1997) Standard Test Method for Particle Size Distribution of Alumina or Quartz by Electric Sensing Zone Technique

-Test Method E1772-95 Standard Test Method for ParticleSize Distribution of Chromatography Media by Electric Sensing Zone Technique

-Test Method F751-83 (1997) Standard Test Method for Measuring Particle Size of Wide-Size Range Dry Toners

-Test Method F577-83 (1997) Standard Test Method for Particle Size Measurement of Dry Toners

-Test Method D4438-85 (1997) Standard Test Method for Particle Size Distribution of Catalytic Material by Electronic Counting
-Practice D3451-92 Standard Practices for Testing Polymeric

-Test Method F662-86 (1992)e1 Standard Test Method for Measurement of Particle Count and Size Distribution in Batch Samples for Filter Evaluation Using an Electrical Resistance Particle Counter

-Specification C757-90 (1996) Standard Specification for Nuclear-Grade Plutonium Dioxide Powder, Sinterable

Additionally, one International Standard Organization (ISO) guideline document has been produced on the Coulter Principle

-INTERNATIONAL STANDARD ISO 13319 Determination of particle size distributions —Electrical sensing zone method Reference number ISO 13319:2000(E)First edition 2000-04-01

Need for Blood Testing due to Nuclear Threat

Wallace H Coulter developed the Coulter Principle in the mid 1940s (though a patent was not awarded until October 20, 1953). It is important to note that Coulter’s development of the Coulter Principle was around August 9, 1945, the day the United States dropped a nuclear bomb on Hiroshima. This event motivated Coulter to simplify and improve blood cell analysis so that large populations could be screened rapidly. Partial funding of the project came from a grant award from the Office of Naval Research. While other sources sometimes relate a story surrounding paint analysis, this is not supported by the historical facts or by people who lived and worked with Coulter over the years. Authoritative resources on the topic are available in Journal of Laboratory Automation, December 2003. The Coulter Principle: Foundation of An Industry and Cytometry volume 10, a DVD series produced by the Purdue University Cytometry Labs.

Relationship to Flow Cytometry

A COULTER COUNTER® played an important role in the development of the first ever cell sorter, and was involved in the early days of the development of flow cytometry. Even today, some flow cytometers utilize the Coulter Principle to provide highly accurate information about cell size and count. Much more information is available in Cytometry volume 10, a DVD series produced by the Purdue University Cytometry Labs.

Previous Article Version

The Coulter principle states that particles pulled through an orifice, concurrent with an electric current
Electric current
Electric current is a flow of electric charge through a medium.This charge is typically carried by moving electrons in a conductor such as wire...

, produce a change in impedance
Electrical impedance
Electrical impedance, or simply impedance, is the measure of the opposition that an electrical circuit presents to the passage of a current when a voltage is applied. In quantitative terms, it is the complex ratio of the voltage to the current in an alternating current circuit...

 that is proportional to the volume of the particle traversing the orifice. This pulse in impedance originates from the displacement of electrolyte caused by the particle. The Coulter principle was named for its inventor, Wallace H. Coulter
Wallace H. Coulter
Wallace H. Coulter was an American electrical engineer, inventor, and businessman. He is best known for his discovery of the Coulter principle, which provided a methodology for counting, measuring and evaluating microscopic particles suspended in fluid...

. when he was working for the Department of Naval Research to standardize the size of solid particles in the paint used on US battleships in order to improve its adherence to the hull. The principle has found commercial success in the medical industry, in particular in hematology
Hematology
Hematology, also spelled haematology , is the branch of biology physiology, internal medicine, pathology, clinical laboratory work, and pediatrics that is concerned with the study of blood, the blood-forming organs, and blood diseases...

, where it can be applied to count and size the various cells that make up whole blood.
The source of this article is wikipedia, the free encyclopedia.  The text of this article is licensed under the GFDL.
 
x
OK