Aircraft engine controls
Encyclopedia
Aircraft engine controls provide a means for the pilot to control and monitor the operation of the aircraft's powerplant. This article describes controls used with a basic internal-combustion engine driving a propeller
. Some optional or more advanced configurations are described at the end of the article. Jet turbine engines
use different operating principles and have their own sets of controls and sensors.
If the aircraft is equipped with a fuel pump:
Propeller (aircraft)
Aircraft propellers or airscrews convert rotary motion from piston engines or turboprops to provide propulsive force. They may be fixed or variable pitch. Early aircraft propellers were carved by hand from solid or laminated wood with later propellers being constructed from metal...
. Some optional or more advanced configurations are described at the end of the article. Jet turbine engines
Jet engine
A jet engine is a reaction engine that discharges a fast moving jet to generate thrust by jet propulsion and in accordance with Newton's laws of motion. This broad definition of jet engines includes turbojets, turbofans, rockets, ramjets, pulse jets...
use different operating principles and have their own sets of controls and sensors.
Basic Controls and Indicators
- Master Switch - Most often actually two separate switches, the Battery Master and the Alternator Master. The Battery Master activates a relay (sometimes called the battery contactor) which connects the battery to the aircraft's main electrical bus. The alternator master activates the alternator by applying power to the alternator field circuit. These two switches provide electrical power to all the systems in the aircraft.
- Throttle - Sets the desired power level. The throttle controls the mass flow-rate of air (in fuel-injected engines) or air/fuel mixture (in carburetted engines) delivered to the cylinders.
- Pitch Control - Adjusts the Constant Speed Unit, which in turn adjusts the propeller pitch and regulates the engine load as necessary to maintain the set R.P.M.
- Mixture Control - Sets the amount of fuel added to the intake airflow. At higher altitudes the air pressure (and therefore the oxygen level) declines so the fuel volume must also be reduced to give the correct air/fuel mixture. This process is known as "leaning".
- Ignition Switch - Activates the magnetoMagneto (electrical)A magneto is an electrical generator that uses permanent magnets to produce alternating current.Magnetos adapted to produce pulses of high voltage are used in the ignition systems of some gasoline-powered internal combustion engines to provide power to the spark plugs...
s by opening the grounding or 'p-lead' circuit; with the p-lead ungrounded the magneto is free to send its high-voltage output to the spark plugs. In most aircraft the ignition switch also applies power to the starter motor during engine start. In piston aircraft engines, the battery does not generate the spark for combustion. This is accomplished using devices called magnetos. Magnetos are connected to the engine by gearing. When the crankshaft turns, it turns the magnetos which mechanically generate voltage for spark. In the event of an electrical failure, the engine will continue to run. The Ignition Switch has the following positions:- Off - Both magneto p-leads are connected to electrical ground. This disables both magnetos, no spark is produced.
- Right - The left magneto p-lead is grounded, and the right is open. This disables the left magneto and enables the right magneto only.
- Left - The right magneto p-lead is grounded, and the left is open. This disables the right magneto and enables the left magneto only.
- Both - This is the normal operating configuration, both p-leads are open enabling both magnetos.
- Start - The pinion gear on the starter motor is engaged with the flywheel and the starter motor runs to turn the engine over. In most cases, only the left magneto is active (the right p-lead is grounded) due to timing differences between the magnetos at low RPMs.
- Tachometer - A gauge to indicate engine speed in revolutions per minute (RPM) or percentage of maximum.
- Manifold Pressure (MP) Gauge - Indicates the absolute pressure in the intake manifold.
- Oil Temperature Gauge - Indicates the engine oil temperature.
- Oil Pressure Gauge - Indicates the supply pressure of the engine lubricant.
- Exhaust Gas Temperature (EGT) Gauge - Indicates the temperature of the exhaust gas just after combustion. Used to set the fuel/air mixture (leaning) correctly.
- Cylinder Head Temperature (CHT) Gauge - Indicates the temperature of at least one of the cylinder heads. Used to set the fuel/air mixture.
- Carburetor Heat Control - Controls the application of heat to the carburetor venturi area to remove or prevent the formation of ice in the throat of the carburetor as well as bypassing the air filter in case of impact icing.
- Alternate Air - Bypasses the air filter on a fuel-injected engine.
Fuel
- Fuel Primer Pump - A manual pump to add a small amount of fuel at the cylinder intakes to assist in starting a cold engine. Fuel injected engines do not have this control. For fuel injected engines, a fuel boost pump is used to prime the engine prior to start.
- Fuel Quantity Gauge - Indicates the amount of fuel remaining in the identified tank. One per fuel tank.
- Fuel Select Valve - Connects the fuel flow from the selected tank to the engine.
If the aircraft is equipped with a fuel pump:
- Fuel Pressure Gauge - Indicates the supply pressure of fuel to the carburetor (or in the case of a fuel injected engine, to the fuel controller.)
- Fuel Boost Pump Switch - Controls the operation of the auxiliary electric fuel pump to provide fuel to the engine before it starts or in case of failure of the engine powered fuel pump. Some large airplanes have a fuel system that allows the flight crew to jettison or dump the fuel. When operated, the boost pumps in the fuel tanks pump the fuel to the dump chutes or jettison nozzles and overboard to atmosphere.
Propeller
If the aircraft is equipped with adjustable-pitch or constant-speed propeller(s):- Propeller Control - Used to set the desired propeller speed. Once the pilot has set the desired propeller speed, the propeller governor maintains that propeller speed by adjusting the pitch of the propeller blades, using the engine's oil pressure to move a hydraulic piston in the propeller hub.
- Manifold Pressure Gauge - Indicates the (absolute) pressure in the engine's intake manifold. When the engine is running normally, there is a good correlation between the intake manifold pressure and the torque the engine is developing.
Cowl
If the aircraft is equipped with adjustable Cowl Flaps:- Cowl Flap Position Control - Cowl Flaps are opened during high power/low airspeed operations like takeoff to maximize the volume of cooling airflow over the engine's cooling fins.
- Cylinder Head Temperature Gauge - Indicates the temperature of all cylinder heads or on a single CHT system, the hottest head. A Cylinder Head Temperature Gauge has a much shorter response time than the oil temperature gauge, so it can alert the pilot to a developing cooling issue more quickly. Engine overheating may be caused by:
- Running too long at a high power setting.
- Poor leaning technique.
- Restricting the volume of cooling airflow too much.
- Insufficient delivery of lubricating oil to the engine's moving parts.