Royal Aircraft Factory H.R.E.2
Encyclopedia
The Royal Aircraft Factory H.R.E.2 was intended as a Naval reconnaissance floatplane. The single example built was serving with the Royal Naval Air Service
Royal Naval Air Service
The Royal Naval Air Service or RNAS was the air arm of the Royal Navy until near the end of the First World War, when it merged with the British Army's Royal Flying Corps to form a new service , the Royal Air Force...
at the start of World War I
World War I
World War I , which was predominantly called the World War or the Great War from its occurrence until 1939, and the First World War or World War I thereafter, was a major war centred in Europe that began on 28 July 1914 and lasted until 11 November 1918...
.
Design and development
The H.R.E.2 was the second aircraft designed by the Royal Aircraft Factory under its Reconnaissance Experimental designation. This team was headed by Chief Engineer Fred Green, but details were by John KenworthyJohn Kenworthy
John Kenworthy B.Sc., F.R.Aes was an English aviation engineer and aircraft designer.John Kenworthy appears in the 1901 Census of Darlington, aged 17, living with four sisters, one brother and his parents George and Ellen Kenworthy at 65 Greenbank Road, Darlington, County Durham...
, who had designed the derivatives of the B.E.3
Royal Aircraft Factory B.E.3
|-See also:-References:* Bruce J.M. The Aeroplanes of the Royal Flying Corps . London: Putnam, 1982. ISBN 0-370-30084-x.* Hare, Paul. The Royal Aircraft Factory. London: Putnam, 1990. ISBN 0-85177-843-7....
, The H stood for hydroplane (sea- or float plane), for the specification came from the Air Department of the Admiralty for the Naval Wing of the R.F.C. It was a two bay biplane with staggered wings of equal span and equal, constant chord. Lateral control was by wing warping. The fuselage was flat sided with a deep rounded decking similar to that of the earlier R.E.1
Royal Aircraft Factory R.E.1
The Royal Aircraft Factory R.E.1 was an experimental two-seat single-engined biplane from before World War I, intended to develop reconnaissance aircraft.-Design and development:...
, though the front cockpit was much longer and more open-sided in the later aircraft. The pilot sat behind, just aft of the wing trailing edge; there was no cut-out for visibility. The elevator and tailplane were both single piece surfaces.
Though it was intended as a floatplane powered by a 100 hp (75 kW) 12-cylinder Renault
Renault
Renault S.A. is a French automaker producing cars, vans, and in the past, autorail vehicles, trucks, tractors, vans and also buses/coaches. Its alliance with Nissan makes it the world's third largest automaker...
engine, it initially flew as a landplane with the smaller 70 hp Renault
Renault 70 hp
|-See also:-Bibliography:* Gunston, Bill. World Encyclopaedia of Aero Engines. Cambridge, England. Patrick Stephens Limited, 1989. ISBN 1-85260-163-9...
aircooled upright V-6 as used in the R.E.1. In this configuration the rudder was mounted above and clear of the tail plane, leaving room for the one piece elevators and having the same shape, roughly a flattened oval with its long axis parallel with the fuselage, as that of the B.E.3
Royal Aircraft Factory B.E.3
|-See also:-References:* Bruce J.M. The Aeroplanes of the Royal Flying Corps . London: Putnam, 1982. ISBN 0-370-30084-x.* Hare, Paul. The Royal Aircraft Factory. London: Putnam, 1990. ISBN 0-85177-843-7....
. The landplane version was often referred to as the R.E.2.
The floats of the H.R.E.2 were fitted at the same time as the more powerful engine. They were typical of the time: a pair of main short floats were mounted to the fuselage by two pairs of struts, those at the front sloping back to around the engine bulkhead and the aft pair running vertically to the point where the front wing spar joined the fuselage. The aircraft sat tail down in the water, the rear supported by a third small double float. A triangular fin was fitted and a new teardrop shaped rudder, cropped at the bottom, mounted on it. The elevator hinge was near the trailing edge of the rudder, giving the elevator clearance to move. The fin and rudder design was essentially repeated on the later R.E.3. The aircraft was seriously damaged in an attempted take off from Frensham Pond
Frensham
Frensham is a village in Surrey, England, beside the A287, south west of Guildford. Neighbouring villages include Millbridge, Shortfield Common, Dockenfield, Spreakley, Batt's Corner and Rushmoor. Frensham lies on the River Wey. Farnham is the nearest main town and it is to the north. The...
and then rebuilt as a landplane once again, fitted with ailerons rather than wing warping. It kept the revised fin and rudder and had a two wheeled, single axle undercarriage mounted on two longitudinal members that projected forwards to form "hockey stick" anti-nose-over skids like those of the B.E.1. In this form it served with the Royal Naval Air Service
Royal Naval Air Service
The Royal Naval Air Service or RNAS was the air arm of the Royal Navy until near the end of the First World War, when it merged with the British Army's Royal Flying Corps to form a new service , the Royal Air Force...
(RNAS) as aircraft no.17 and was still in service at the start of World War I. It was wrecked in a crash on 10 February 1915.